- 您現在的位置：買賣IC網 > PDF目錄67723 > ISP1564ET,551 (ST-ERICSSON) PCI BUS CONTROLLER, PBGA100 PDF資料下載
參數資料
| 型號： | ISP1564ET,551 |
| 廠商： | ST-ERICSSON |
| 元件分類： | 總線控制器 |
| 英文描述： | PCI BUS CONTROLLER, PBGA100 |
| 封裝： | 9 X 9 MM, 0.70 MM HEIGHT, 0.80 MM PITCH, PLASTIC, SOT926-1, TFBGA-100 |
| 文件頁數： | 58/99頁 |
| 文件大?。?/td> | 493K |
| 代理商： | ISP1564ET,551 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁
ISP1564_2
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 — 13 November 2008
60 of 98
NXP Semiconductors
ISP1564
HS USB PCI host controller
11.2 EHCI controller capability registers
Other than the OHCI host controller, there are some registers in EHCI that dene the
capability of EHCI. The address range of these registers is located before operational
registers.
11.2.1 CAPLENGTH/HCIVERSION register
The bit allocation of this 4-byte register is given in Table 93.
3
POCI
On read Port Overcurrent Indicator: This bit is valid only when the root hub is congured to show
overcurrent conditions are reported on a per-port basis. If the per-port overcurrent reporting is not
supported, this bit is set to logic 0. If cleared, all power operations are normal for this port. If set, an
overcurrent condition exists on this port.
0 — No overcurrent condition.
1 — Overcurrent condition detected.
On write Clear Suspend Status: The HCD can write logic 1 to initiate a resume. Writing logic 0 has
no effect. A resume is initiated only if PSS (Port Suspend Status) is set.
2
PSS
On read Port Suspend Status: This bit indicates whether the port is suspended or is in the resume
sequence. It is set by a Set Suspend State write and cleared when PSSC (Port Suspend Status
Change) is set at the end of the resume interval. This bit is not set if CCS (Current Connect Status)
is cleared. This bit is also cleared when PRSC is set at the end of the port reset or when the host
controller is placed in the USBRESUME state. If an upstream resume is in progress, it will
propagate to the host controller.
0 — Port is not suspended.
1 — Port is suspended.
On write Set Port Suspend: The HCD can set the PSS (Port Suspend Status) bit by writing logic 1
to this bit. Writing logic 0 has no effect. If CCS is cleared, this write does not set PSS; instead it sets
CSS. This informs the driver that it attempted to suspend a disconnected port.
1
PES
On read Port Enable Status: This bit indicates whether the port is enabled or disabled. The root
hub may clear this bit when an overcurrent condition, disconnect event, switched-off power or
operational bus error is detected. This change also causes Port Enabled Status Change to be set.
The HCD can set this bit by writing Set Port Enable and clear it by writing Clear Port Enable. This bit
cannot be set when CCS (Current Connect Status) is cleared. This bit is also set on completing a
port reset when Reset Status Change is set or on completing a port suspend when Suspend Status
Change is set.
0 — Port is disabled.
1 — Port is enabled.
On write Set Port Enable: The HCD can set PES (Port Enable Status) by writing logic 1. Writing
logic 0 has no effect. If CCS is cleared, this write does not set PES, but instead sets CSC (Connect
Status Change). This informs the driver that it attempted to enable a disconnected port.
0
CCS
On read Current Connect Status: This bit reects the current state of the downstream port.
0 — No device is connected.
1 — Device is connected.
On write Clear Port Enable: The HCD can write logic 1 to this bit to clear the PES (Port Enable
Status) bit. Writing logic 0 has no effect. The CCS bit is not affected by any write.
Remark: This bit always reads logic 1 when the attached device is nonremovable
(DeviceRemovable[NDP]).
Table 92.
HcRhPortStatus[2:1] - Host Controller Root Hub Port Status[2:1] register bit description …continued
Address: Content of the base address register + 54h
Bit
Symbol
Description
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1582BS,557 | UNIVERSAL SERIAL BUS CONTROLLER, PQCC56 |
| ISP1583ET1,118 | UNIVERSAL SERIAL BUS CONTROLLER, PBGA64 |
| ISP1583BS,551 | UNIVERSAL SERIAL BUS CONTROLLER, PQCC64 |
| ISP1583ET2 | UNIVERSAL SERIAL BUS CONTROLLER, PBGA64 |
| ISP1761ET,518 | UNIVERSAL SERIAL BUS CONTROLLER, PBGA128 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1564ETGA | 功能描述:IC USB PCI HOST CTRLR 100-TFBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| ISP1564ET-S | 功能描述:外圍驅動器與原件 - PCI USB 2.0 2PORT PCI HOST CONTROL RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| ISP1564ET-T | 功能描述:外圍驅動器與原件 - PCI USB 2.0 2PORT PCI HOST CONTROL RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| ISP1564ETUM | 功能描述:IC USB PCI HOST CTRLR 100-TFBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| ISP1564HL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Hi-Speed USB PCI host controller |
發布緊急采購，3分鐘左右您將得到回復。