- 您現在的位置：買賣IC網 > PDF目錄372405 > SZF2002HL (NXP SEMICONDUCTORS) Low voltage 8-bit microcontroller with 6-kbyte embedded RAM PDF資料下載
參數資料
| 型號： | SZF2002HL |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Low voltage 8-bit microcontroller with 6-kbyte embedded RAM |
| 中文描述： | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 12 X 12 MM, 1.40 MM HEIGHT, PLASTIC, SOT-315-1, LQFP-80 |
| 文件頁數： | 72/76頁 |
| 文件大?。?/td> | 431K |
| 代理商： | SZF2002HL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁當前第72頁第73頁第74頁第75頁第76頁
1998 Aug 26
72
Philips Semiconductors
Product specification
Low voltage 8-bit microcontroller with
6-kbyte embedded RAM
SZF2002
29 SOLDERING
29.1
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(order code 9398 652 90011).
29.2
Reflow soldering
Reflow soldering techniques are suitable for all LQFP
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
infrared/convection heating in a conveyor type oven.
Throughput times (preheating, soldering and cooling) vary
between 50 and 300 seconds depending on heating
method. Typical reflow peak temperatures range from
215 to 250
°
C.
29.3
Wave soldering
Wave soldering is
not
recommended for LQFP packages.
This is because of the likelihood of solder bridging due to
closely-spaced leads and the possibility of incomplete
solder penetration in multi-lead devices.
CAUTION
Wave soldering is NOT applicable for all LQFP
packages with a pitch (e) equal or less than 0.5 mm.
If wave soldering cannot be avoided, for LQFP
packages with a pitch (e) larger than 0.5 mm, the
following conditions must be observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave)
soldering technique should be used.
The footprint must be at an angle of 45
°
to the board
direction and must incorporate solder thieves
downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260
°
C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
°
C within
6 seconds. Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
29.4
Repairing soldered joints
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300
°
C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| T1012D | STANDARD TRIACS |
| T1012DH | STANDARD TRIACS |
| T1012M | STANDARD TRIACS |
| T1012MH | STANDARD TRIACS |
| T1012N | STANDARD TRIACS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SZF-41T-P0.7 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Disconnectable Crimp style Wire-to-wire connectors |
| SZFP6F0A | 制造商:SEOUL 制造商全稱:Seoul Semiconductor 功能描述:Z Power LED - Super high Flux output and high Luminance |
| SZG05A0A | 功能描述:大功率LED - 單色 Green 525nm 70lm 350mA RoHS:否 制造商:Cree, Inc. 照明顏色:Blue 波長:465 nm 光強度: 光通量/輻射通量:500 mW 正向電流:350 mA 正向電壓:3.1 V 安裝風格:SMD/SMT 功率額定值: 系列:XB-D 封裝:Reel |
| SZG05A0A-1B | 制造商:Seoul Semiconductor 功能描述:Z5 Series Green LED 70lm Typical |
| SZG40237-36RL | 制造商:Motorola Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。