www.ti.com
TMS320TCI6482
Communications Infrastructure Digital Signal Processor
SPRS246F–APRIL 2005–REVISED MAY 2007
Table 2-3. Terminal Functions (continued)
SIGNAL
NAME
MULTICHANNEL BUFFERED SERIAL PORT 1 AND MULTICHANNEL BUFFERED SERIAL PORT 0 (McBSP1 and McBSP0)
McBSP external clock source (as opposed to internal) (
I
)
CLKS
AJ4
I
IPD
[shared by McBSP1 and McBSP0]
MULTICHANNEL BUFFERED SERIAL PORT 1 (McBSP1)
CLKR1/GP[0]
AF4
I/O/Z
IPD
McBSP1 receive clock (
I/O/Z
) or GP[0] (
I/O/Z
) [default]
VLYNQ transmit data pin [2] (
O
) or McBSP1 receive frame sync (
I/O/Z
) or
VTXD2/FSR1/GP[10]
AE5
I/O/Z
IPD
GP[10] (
I/O/Z
)[default]
VLYNQ transmit data pin [0] (
O
) or McBSP1 receive data (
I
) or GP[8] (
I/O/Z
)
VTXD0/DR1/GP[8]
AH5
I/O/Z
IPD
[default]
VLYNQ transmit data pin [1] (
O
) or McBSP1 transmit data (
O/Z
) or GP[9]
VTXD1/DX1/GP[9]
AG5
I/O/Z
IPD
(
I/O/Z
) [default]
VLYNQ transmit data pin [3] (
O
) or McBSP1 transmit frame sync (
I/O/Z
) or
VTXD3/FSX1/GP[11]
AG4
I/O/Z
IPD
GP[11] (
I/O/Z
) [default]
CLKX1/GP[3]
AF5
I/O/Z
IPD
McBSP1 transmit clock (
I/O/Z
) or GP[3] (
I/O/Z
) [default]
MULTICHANNEL BUFFERED SERIAL PORT 0 (McBSP0)
VCLK/CLKR0
AG1
I/O/Z
IPU
VLYNQ (
I/O
) [default] or McBSP0 receive clock (
I/O/Z
)
VRXD2/FSR0
AH3
I/O/Z
IPD
VLYNQ receive data pin [2] (
I
) [default] or McBSP0 receive frame sync (
I/O/Z
)
VRXD0/DR0
AJ5
I
IPD
VLYNQ receive data pin [0] (
I
) [default] or McBSP0 receive data (
I
)
VRXD1/DX0
AF6
I/O/Z
IPD
VLYNQ receive data pin [1] (
I
) [default] or McBSP0 transmit data (
O/Z
)
VRXD3/FSX0
AJ3
I/O/Z
IPD
VLYNQ receive data pin [3] (
I
) [default] or McBSP0 transmit frame sync (
I/O/Z
)
VSCRUN/CLKX0
AG6
I/O/Z
IPU
VLYNQ serial clock run request (
I/O
) [default] or McBSP0 transmit clock (
I/O/Z
)
UNIVERSAL TEST AND OPERATIONS PHY INTERFACE for ASYNCHRONOUS TRANSFER MODE (ATM) [UTOPIA SLAVE]
UTOPIA SLAVE (ATM CONTROLLER) - TRANSMIT INTERFACE
Source clock for UTOPIA transmit driven by Master ATM Controller.
When the UTOPIA peripheral is disabled (UTOPIA_EN [AEA12 pin] = 0), this
UXCLK/MTCLK/
N4
I/O/Z
pin is either EMAC MII transmit clock (MTCLK) or the EMAC RMII reference
RMREFCLK
clock. The EMAC function is controlled by the MACSEL[1:0] (AEA[10:9] pins).
For more detailed information, see
Section 3
,
Device Configuration
.
Transmit cell available status output signal from UTOPIA Slave.
0 indicates a complete cell is NOT available for transmit
UXCLAV/GMTCLK
K5
I/O/Z
1 indicates a complete cell is available for transmit
When the UTOPIA peripheral is disabled (UTOPIA_EN [AEA12 pin] = 0), this
pin is EMAC GMII transmit clock. MACSEL[1:0] dependent.
UTOPIA transmit interface enable input signal. Asserted by the Master ATM
Controller to indicate that the UTOPIA Slave should put out on the Transmit
Data Bus the first byte of valid data and the UXSOC signal in the next clock
UXENB/MTXEN/
J5
I/O/Z
cycle.
RMTXEN
When the UTOPIA peripheral is disabled (UTOPIA_EN [AEA12 pin] = 0), this
pin is either the EMAC MII transmit enable [default] or EMAC RMII transmit
enable or EMAC GMII transmit enable. MACSEL[1:0] dependent.
Transmit Start-of-Cell signal. This signal is output by the UTOPIA Slave on the
rising edge of the UXCLK, indicating that the first valid byte of the cell is
available on the 8-bit Transmit Data Bus (UXDATA[7:0]).
UXSOC/MCOL
K3
I/O/Z
When the UTOPIA peripheral is disabled (UTOPIA_EN [AEA12 pin] = 0), this
pin is either the EMAC MII collision sense or EMAC GMII collision sense.
MACSEL[1:0] dependent.
UXADDR4/MDCLK
M5
I
UTOPIA transmit address pins (UXADDR[4:0]) (
I
)
As UTOPIA transmit address pins, UTOPIA_EN (AEA12 pin) = 1:
UXADDR3/MDIO
N3
I
5-bit Slave transmit address input pins driven by the Master ATM Controller
UXADDR2/PCBE3
P5
I
to identify and select one of the Slave devices (up to 31 possible) in the
ATM System.
UXADDR1/PIDSEL
R3
I
TYPE
(1)
IPD/IPU
(2)
DESCRIPTION
NO.
When the UTOPIA peripheral is disabled (UTOPIA_EN [AEA12 pin] = 0) and if
the PCI_EN pin = 1, these pins are PCI peripheral pins:
PCI command/byte enable 3(PCBE3) [
I/O/Z
],
PCI initialization device select (PIDSEL) [
I
], and
PCI target ready (PTRDY) [
I/O/Z
].
UXADDR0/PTRDY
P4
I
Submit Documentation Feedback
Device Overview
35