參數資料
型號: AM79C971
廠商: Advanced Micro Devices, Inc.
英文描述: PCnet⑩-FAST Single-Chip Full-Duplex 10/100 Mbps Ethernet Controller for PCI Local Bus
中文描述: PCnet⑩快速單芯片全雙工10/100 Mbps以太網控制器,PCI總線
文件頁數: 76/265頁
文件大小: 3190K
代理商: AM79C971
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁當前第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁第262頁第263頁第264頁第265頁
76
Am79C971
transmitted, the XMTFW bits (CSR80, bits 9-8) al-
ways
govern when transmit DMA is requested.
I
Successful reception of the first 64 bytes of every
receive frame is not a requirement for Receive DMA
to begin as described in the Receive Exception
Conditions section. Instead, receive DMA will be re-
quested as soon as either the RCVFW threshold
(CSR80, bits 12-13) is reached or a complete valid
receive frame is detected, regardless of length. This
Receive FIFO operation is identical to when the
RPA bit (CSR124, bit 3) is set during half-duplex
mode operation.
The MAC engine changes for full-duplex operation are
as follows:
I
Changes to the Transmit Deferral mechanism:
Transmission is not deferred while receive is
active.
The IPG counter which governs transmit deferral
during the IPG between back-to-back transmits
is started when transmit activity for the first
packet ends, instead of when transmit and car-
rier activity ends.
I
When the AUI or MII port is active, Loss of Carrier
(LCAR) reporting is disabled (LCAR is still reported
when the 10BASE-T port is active if a packet is
transmitted while in Link Fail state).
I
The 4.0
μ
s carrier sense blinding period after a
transmission during which the SQE test normally
occurs is disabled.
I
When the AUI port is active, the SQE Test error re-
porting (CERR) is disabled (CERR is still reported
when the 10BASE-T port is active if a packet is
transmitted while in Link Fail state).
I
The collision indication input to the MAC engine is
ignored.
The T-MAU changes for full-duplex operation are as fol-
lows:
I
The transmit to receive loopback path in the T-MAU
is disabled.
I
The collision detect circuit is disabled.
I
The SQE test function is disabled.
The MII changes for full-duplex operation are as fol-
lows:
I
The collision detect (COL) pin is disabled.
I
The SQE test function is disabled.
Full-Duplex Link Status LED Support
The Am79C971 controller provides bits in each of the
LED Status registers (BCR4, BCR5, BCR6, BCR7) to
display the Full-Duplex Link Status. If the FDLSE bit
(bit 8) is set, a value of 1 will be sent to the associated
LEDOUT bit when the T-MAU is in the Full-Duplex
Link Pass state only.
Media Independent Interface
The Am79C971 controller fully supports the MII ac-
cording to the IEEE 802.3 standard. This Reconcilia-
tion Sublayer interface allows a variety of PHYs
(100BASE-TX, 100BASE-FX, 100BASE-T4,
100BASE-T2, 10BASE-T, etc.) to be attached to the
Am79C971 MAC engine without future upgrade prob-
lems. The MII interface is a 4-bit (nibble) wide data path
interface that runs at 25 MHz for 100-Mbps networks
and 2.5 MHz for 10-Mbps networks. The interface con-
sists of two independent data paths, receive
(RXD(3:0)) and transmit (TXD(3:0)), control signals for
each data path (RX_ER, RX_DV, TX_ER, TX_EN), net-
work status signals (COL, CRS), clocks (RX_CLK,
TX_CLK) for each data path, and a two-wire manage-
ment interface (MDC and MDIO). See Figure 38.
MII Transmit Interface
The MII transmit clock is generated by the external
PHY and is sent to the Am79C971 controller on the
TX_CLK input pin. The clock can run at 25 MHz or 2.5
MHz, depending on the speed of the network that the
external PHY is attached to. The data is a nibble-wide
(4 bits) data path, TXD(3:0), from the Am79C971 con-
troller to the external PHY and is synchronous to the
rising edge of TX_CLK. The transmit process starts
when the Am79C971 controller asserts the TX_EN,
which indicates to the external PHY that the data on
TXD(3:0) is valid.
Normally, unrecoverable errors are signaled through
the MII to the external PHY with the TX_ER output pin.
The external PHY will respond to this error by generat-
ing a TX coding error on the current transmitted frame.
The Am79C971 controller does not use this method of
signaling errors on the transmit side. The Am79C971
controller will invert the FCS on the last byte generating
an invalid FCS. The TX_ER pin is reserved for future
use and is actively driven to 0.
MII Receive Interface
The MII receive clock is also generated by the external
PHY and is sent to the Am79C971 controller on the
RX_CLK input pin. The clock will be the same fre-
quency as the TX_CLK but will be out of phase and can
run at 25 MHz or 2.5 MHz, depending on the speed of
the network the external PHY is attached to. The
RX_CLK is a continuous clock during the reception of
the frame, but can be stopped for up to two RX_CLK
periods at the beginning and the end of frames, so that
the external PHY can sync up to the network data traffic
necessary to recover the receive clock. During this
time, the external PHY may switch to the TX_CLK to
maintain a stable clock on the receive interface. The
Am79C971 controller will handle this situation with no
loss of data. The data is a nibble-wide (4 bits) data
相關PDF資料
PDF描述
AM79C971KCW IC LOGIC 16211 24-BIT FET BUS SWITCH -40+85C TSSOP-56 35/TUBE
AM79C972BKCW PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support
AM79C972BKIW PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support
AM79C972BVCW PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support
AM79C972 PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support
相關代理商/技術參數
參數描述
AM79C971AKC 制造商:Advanced Micro Devices 功能描述:
AM79C971AVC 制造商:Advanced Micro Devices 功能描述:10/100 MBPS ETHERNET - Trays
AM79C971AVC\\W 制造商:Rochester Electronics LLC 功能描述:- Bulk
AM79C971AVC\W 制造商:Rochester Electronics LLC 功能描述:- Bulk
AM79C971AWW WAF 制造商:Advanced Micro Devices 功能描述: