參數資料
| 型號： | CS8952-IQZ |
| 廠商： | Cirrus Logic Inc |
| 文件頁數： | 63/81頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX 100/10 PHY 100TQFP |
| 標準包裝： | 90 |
| 類型： | 收發(fā)器 |
| 規(guī)程： | MII |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP |
| 供應商設備封裝： | 100-TQFP（14x14） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 759 (CN2011-ZH PDF) |
| 其它名稱： | 598-1208 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁當前第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
CS8952
CrystalLAN 100BASE-X and 10BASE-T Transceiver
66
DS206F1
ly) on both sides of the TX+/- traces.
No signal current carrying planes, i.e. no
ground or power plane, should be present un-
derneath the region between the transformer
secondary (network) side and the RJ-45. How-
ever, a chassis plane may be added in this re-
gion to pick up the metal tabs of a shielded RJ-
45. This chassis plane should be separated from
the ground and power planes by at least
50 mils. That is, all other ground and power
planes should be “cookie cuttered” so they are
voided in the area of the chassis plane. Gener-
ally speaking, parts should not cross the moat
except for the transformer.
Proper termination practices must be used with
all transmission lines, especially if sending and
receiving high speed signals on and off the
board. Series terminations must be kept close to
the source and load terminations close to the
load. Thus the TX_NRZ+/- termination com-
ponents must be kept close to the fiber optic
transceiver, and the RX_NRZ+/- and SIG-
NAL+/- termination components must be kept
close to the CS8952.
Locate the crystal as close to the CS8952 as
possible, running short traces on the component
side in order to reduce parasitic load capaci-
tance.
Add bulk capacitance at each connector where
power may be supplied. For example, MII pow-
er may be provided at the MII connector and at
a separate connector for test purposes. If so, and
the two connectors are not adjacent, then the
bulk capacitors should be duplicated in each lo-
cations.
Use wide traces to connect the “Bob Smith” ter-
mination resistors at T1 and the RJ-45 to the
2 kV capacitor or capacitors in order to mini-
mize their lead inductance.
CS8952 Pin
Assignment
T1 Primary Pin
Assignment
T1 Secondary
Pin Assignment
RJ-45 Pin Assignment
Adapter/NIC
Configuration
Hub/Repeater
Configuration
91 (RX+)
1 (RX+)
7 (RX+)
3 (RD+)
1 (RD+)
92 (RX-)
2 (RX-)
6 (RX-)
6 (RD-)
2 (RD-)
81 (TX-)
16 (TX-)
10 (TX-)
2 (TD+)
6 (TD-)
80 (TX+)
15 (TX+)
11 (TX+)
1 (TD+)
3 (TD+)
Table 8. RJ-45 Wiring
相關PDF資料 |
PDF描述 |
|---|---|
| CY8CLED04DOCD1-56LTXI | IC POWERPSOC DEBUG 4CH 1A 56VQFN |
| CYG2217 | IC MOD PHONE LINE WIRE 1.07" PCB |
| DAC312ER | IC DAC 12BIT MULT HS 20-CDIP |
| DAC8143FPZ | IC DAC 12BIT DAISYCHAIN 16DIP |
| DAC8228FSZ | IC DAC 8BIT DUAL V-OUT 20SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS8952-IQZR | 功能描述:以太網 IC IC 100BASE-TX and 10BASE-T Transceiver RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發(fā)器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| CS8952T | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:100BASE E-X AND 10BASE-T TRANSCEIVER |
| CS8952T-CQ | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:100BASE E-X AND 10BASE-T TRANSCEIVER |
| CS8952T-IQ | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:100BASE E-X AND 10BASE-T TRANSCEIVER |
| CS8952T-IQR | 制造商:Cirrus Logic 功能描述:ETHERNET TXRX SGL CHIP 1-PORT 5V 10MBPS/100MBPS 100TQFP - Tape and Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。