- 您現在的位置：買賣IC網 > PDF目錄371179 > T8301 T8301 Internet Protocol Telephone Phone-On-A-Chip⑩ IP Solution DSP PDF資料下載
參數資料
| 型號： | T8301 |
| 英文描述： | T8301 Internet Protocol Telephone Phone-On-A-Chip⑩ IP Solution DSP |
| 中文描述： | T8301因特網協議電話熱線電話在一個芯片⑩DSP的IP解決方案 |
| 文件頁數： | 59/190頁 |
| 文件大小： | 1535K |
| 代理商： | T8301 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁
Data Sheet
March 2000
DSP1627 Digital Signal Processor
Lucent Technologies Inc.
23
4 Hardware Architecture
(continued)
4.9 Bit Input/Output Unit (BIO)
The BIO controls the directions of eight bidirectional con-
trol I/O pins, IOBIT[7:0]. If a pin is configured as an output,
it can be individually set, cleared, or toggled. If a pin is
configured as an input, it can be read and/or tested.
The lower half of the
sbit
register (see Table 33) contains
current values (VALUE[7:0]) of the eight bidirectional pins
IOBIT[7:0]. The upper half of the
sbit
register (DI-
REC[7:0]) controls the direction of each of the pins. A log-
ic 1 configures the corresponding pin as an output; a logic
0 configures it as an input. The upper half of the
sbit
reg-
ister is cleared upon reset.
The
cbit
register (see Table 34) contains two 8-bit fields,
MODE/MASK[7:0] and DATA/PAT[7:0]. The values of
DATA/PAT[7:0] are cleared upon reset. The meaning of a
bit in either field depends on whether it has been config-
ured as an input or an output in
sbit
. If a pin has been con-
figured to be an output, the meanings are MODE and
DATA. For an input, the meanings are MASK and PAT
(pattern). Table 9 shows the functionality of the MODE/
MASK and DATA/PAT bits based on the direction select-
ed for the associated IOBIT pin.
Those bits that have been configured as inputs can be in-
dividually tested for 1 or 0. For those inputs that are being
tested, there are four flags produced: allt (all true), allf (all
false), somet (some true), and somef (some false). These
flags can be used for conditional branch or special in-
structions. The state of these flags can be saved and re-
stored by reading and writing bits 0 to 3 of the
alf
register
(see Table 35).
If a BIO pin is switched from being configured as an out-
put to being configured as an input and then back to be-
ing configured as an output, the pin retains the previous
output value.
Pin Multiplexing
Please refer to Pin Multiplexing in Section 4.1 for a
description of BIO, PHIF, VEC[3:0], and SIO2 pins.
4.10 Timer
The interrupt timer is composed of the timerc (control)
register, the timer0 register, the prescaler, and the
counter itself. The timer control register (see Table 31,
timerc Register) sets up the operational state of the timer
and prescaler. The timer0 register is used to hold the
counter reload value (or period register) and to set the
initial value of the counter. The prescaler slows the clock
to the timer by a number of binary divisors to allow for a
wide range of interrupt delay periods.
The counter is a 16-bit down counter that can be loaded
with an arbitrary number from software. It counts down
to 0 at the clock rate provided by the prescaler. Upon
reaching 0 count, a vectored interrupt to program ad-
dress 0x10 is issued to the DSP1627, providing the in-
terrupt is enabled (bit 8 of inc and ins registers). The
counter will then either wait in an inactive state for anoth-
er command from software, or will automatically repeat
the last interrupting period, depending upon the state of
the RELOAD bit in the timerc register.
When RELOAD is 0, the counter counts down from its
initial value to 0, interrupts the DSP1627, and then stops,
remaining inactive until another value is written to the
timer0 register. Writing to the timer0 register causes
both the counter and the period register to be written with
the specified 16-bit number. When RELOAD is 1, the
counter counts down from its initial value to 0, interrupts
the DSP1627, automatically reloads the specified initial
value from the period register into the counter, and re-
peats indefinitely. This provides for either a single timed
interrupt event or a regular interrupt clock of arbitrary pe-
riod.
The timer can be stopped and started by software, and
can be reloaded with a new period at any time. Its count
value, at the time of the read, can also be read by soft-
ware. Due to pipeline stages, stopping and starting the
timer may result in one inaccurate count or prescaled pe-
riod. When the DSP1627 is reset, the bottom 6 bits of the
timerc register and the timer0 register and counter are
initialized to 0. This sets the prescaler to CKO/2*, turns
off the reload feature, disables timer counting, and initial-
izes the timer to its inactive state. The act of resetting the
chip does not cause a timer interrupt. Note that the peri-
od register is not initialized on reset.
The T0EN bit of the timerc register enables the clock to
the timer. When T0EN is a 1, the timer counts down to-
wards 0. When T0EN is a 0, the timer holds its current
count.
*
Frequency of CKO/2 is equivalent to either CKI/2 for the PLL by-
passed or related to CKI by the PLL multiplying factors. See Section
4.12, Clock Synthesis.
Table 9. BIO Operations
DIREC[n]
*
*
0
≤
n
≤
7.
MODE/
MASK[n]
0
0
1
1
0
0
1
1
DATA/
PAT[n]
0
1
0
1
0
1
0
1
Action
1 (Output)
1 (Output)
1 (Output)
1 (Output)
0 (Input)
0 (Input)
0 (Input)
0 (Input)
Clear
Set
No Change
Toggle
No Test
No Test
Test for Zero
Test for One
相關PDF資料 |
PDF描述 |
|---|---|
| T8302 | T8302 Internet Protocol Telephone Advanced RISC Machine (ARM) Ethernet QoS Using IEEE 802.1q |
| T8502 | T8502 and T8503 Dual PCM Codecs with Filters |
| T8503 | T8502 and T8503 Dual PCM Codecs with Filters |
| T8531A | T8531A/8532 Multichannel Programmable Codec Chip Set |
| T8531 | T8502 and T8503 Dual PCM Codecs with Filters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T8301AX | 制造商:MOLEX 制造商全稱:Molex Electronics Ltd. 功能描述:Terminator Die |
| T8301BX | 制造商:MOLEX 制造商全稱:Molex Electronics Ltd. 功能描述:Terminator Die |
| T8301DX | 制造商:MOLEX 制造商全稱:Molex Electronics Ltd. 功能描述:Terminator Die |
| T8302 | 制造商:AGERE 制造商全稱:AGERE 功能描述:T8302 Internet Protocol Telephone Advanced RISC Machine (ARM) Ethernet QoS Using IEEE 802.1q |
| T8302A | 制造商:MOLEX 制造商全稱:Molex Electronics Ltd. 功能描述:Terminator Die |
發布緊急采購，3分鐘左右您將得到回復。