參數資料
型號： XRT86VL32IB
廠商： EXAR CORP
元件分類： 數字傳輸電路
英文描述： Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
中文描述： DATACOM, FRAMER, PBGA225
封裝： 19 X 19 MM, 1 MM PITCH, PLASTIC, BGA-225
文件頁數： 74/174頁
文件大?。?/td> 903K
代理商： XRT86VL32IB
XRT86VL32
69
DUAL T1/E1/J1 FRAMER/LIU COMBO - E1 REGISTER DESCRIPTION
REV. V1.2.0
2
Tx_IDLE
R/W
0
Transmit Idle (Flag Sequence Byte)
This bit configures the Transmit HDLC Controller Block #2 to uncon-
ditionally transmit a repeating string of Flag Sequence octets (0X7E)
in the data link channel to the Remote terminal. In normal condi-
tions, the Transmit HDLC Controller block will repeatedly transmit
the Flag Sequence octet whenever there is no MOS message to
transmit to the remote terminal equipment. However, if the user
invokes this “Transmit Idle Sequence” feature, then the Transmit
HDLC Controller block will UNCONDITIONALLY transmit a repeat-
ing stream of the Flag Sequence octet (thereby overwriting all out-
bound MOS data-link messages).
0 - Configures the Transmit HDLC Controller Block # 2 to transmit
data-link information in a “normal” manner.
1 - Configures the Transmit HDLC Controller block # 2 to transmit a
repeating string of Flag Sequence Octets (0x7E).
N
OTE
:
This bit is ignored if the
Transmit
HDLC2 controller is
operating in the BOS Mode - bit 0 (MOS/BOS) within this
register is set to 0.
1
Tx_FCS_EN
R/W
0
Transmit LAPD Message with Frame Check Sequence (FCS)
This bit permits the user to configure the Transmit HDLC Controller
block # 2 to compute and append FCS octets to the “back-end” of
each outbound MOS data-link message.
0 - Configures the Transmit HDLC Controller block # 2 to NOT com-
pute and append the FCS octets to the back-end of each outbound
MOS data-link message.
1 - Configures the Transmit HDLC Controller block # 2 TO COM-
PUTE and append the FCS octets to the back-end of each outbound
MOS data-link message.
N
OTE
:
This bit is ignored if the transmit HDLC2 controller has been
configured to operate in the BOS mode - bit 0 (MOS/BOS)
within this register is set to 0.
0
MOS/BOS
R/W
0
Message Oriented Signaling/Bit Oriented Signaling Send
This bit permits the user to enable LAPD transmission through
HDLC Controller Block # 2 using either BOS (Bit-Oriented Signaling)
or MOS (Message-Oriented Signaling) frames.
0 - Transmit HDLC Controller block # 2 BOS message Send.
1 - Transmit HDLC Controller block # 2 MOS message Send.
N
OTE
:
This is not an Enable bit. This bit must be set to "0" each
time a BOS is to be sent.
T
ABLE
55: D
ATA
L
INK
C
ONTROL
R
EGISTER
(DLCR2) H
EX
A
DDRESS
: 0
X
n143
B
IT
F
UNCTION
T
YPE
D
EFAULT
D
ESCRIPTION
-O
PERATION
相關PDF資料
PDF描述
XRT86VL34_07 Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
XRT86VL34_1 Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
XRT86VL34 Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
XRT86VL34_2 Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
XRT86VL34IB Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
相關代理商/技術參數
參數描述
XRT86VL32IB-F 功能描述:網絡控制器與處理器 IC 1-Ch T1/E1/J1 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT86VL34 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION
XRT86VL34_07 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD T1/E1/J1 FRAMER/LIU COMBO - E1 REGISTER DESCRIPTION
XRT86VL34_1 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD T1/E1/J1 FRAMER/LIU COMBO - HARDWARE DESCRIPTION
XRT86VL34_2 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*