- 您現在的位置：買賣IC網 > PDF目錄366550 > AM79C974 (Advanced Micro Devices, Inc.) PCnetTM-SCSI Combination Ethernet and SCSI Controller for PCI Systems PDF資料下載
參數資料
| 型號： | AM79C974 |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | PCnetTM-SCSI Combination Ethernet and SCSI Controller for PCI Systems |
| 中文描述： | PCnetTM -的SCSI結合以太網和SCSI控制器PCI系統 |
| 文件頁數： | 66/153頁 |
| 文件大小： | 838K |
| 代理商： | AM79C974 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁當前第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁
AMD
P R E L I M I N A R Y
66
Am79C974
EEPROM Microwire Access
The Am79C974 controller contains a built-in capability
for reading and writing to an external EEPROM. This
built-in capability consists of a Microwire interface for di-
rect connection to a Microwire compatible EEPROM, an
automatic EEPROM read feature, and a user-program-
mable register that allows direct access to the Microwire
interface pins.
Automatic EEPROM Read Operation
Shortly after the deassertion of the
RST
pin, the
Am79C974 controller will read the contents of the
EEPROM that is attached to the Microwire interface.
Because of this automatic-read capability of the
Am79C974 controller, an EEPROM can be used to pro-
gram many of the features of the Am79C974 controller
at power-up, allowing system-dependent configuration
information to be stored in the hardware, instead of in-
side of operatingcode.
If an EEPROM exists on the Microwire interface, the
Am79C974 controller will read the EEPROM contents at
the end of the H_RESET operation. The EEPROM con-
tents will be serially shifted into a temporary register and
then sent to various register locations on board the
Am79C974 controller. The host can access the PCI
Configuration Space during the EEPROM read opera-
tions. Access to the Am79C974 I/O resources, however,
is not possible during the EEPROM read operation. The
Am79C974 controller will terminate these I/O accesses
with the assertion of
DEVSEL
and
STOP
while
TRDY
is
not asserted, signaling to the initiator to retry the access
at a later time.
A checksum verification is performed on the data that is
read from the EEPROM. If the checksum verification of
the EEPROM data fails, then at the end of the EEPROM
read sequence, the Am79C974 controller will force all
EEPROM-programmable BCR registers back to their
H_RESET default values. The content of the APROM
locations (offsets 0h – Fh from the I/O base address),
however, will not be cleared. The 8-bit checksum for the
entire 36 bytes of the EEPROM should be FFh.
If no EEPROM is present at the time of the automatic
read operation, then the Am79C974 controller will rec-
ognize this condition and will abort the automatic read
operation and reset both the PREAD and PVALID bits in
BCR19. All EEPROM-programmable BCR registers will
be assigned their default values after H_RESET. The
content of the Address PROM locations (offsets 0h – Fh
from the I/O base address) will be undefined.
If the user wishes to modify any of the configuration bits
that are contained in the EEPROM, then the seven com-
mand, data and status bits of BCR19 can be used to
write to the EEPROM. After writing to the EEPROM, the
host should set the PREAD bit of BCR19. This action
forces a Am79C974 controller re-read of the EEPROM
so that the new EEPROM contents will be loaded into
the EEPROM-programmable registers on board the
Am79C974 controller. (The EEPROM-programmable
registers may also be reprogrammed directly, but only
information that is stored in the EEPROM will be pre-
served at system power-down.) When the PREAD bit of
BCR19 is set, it will cause the Am79C974 controller to
terminate further accesses to internal I/O resources with
the PCI retry cycle. Accesses to the PCI configuration
space is still possible.
EEPROM Auto-Detection
The Am79C974 controller uses the EESK/
LED1
pin to
determine if an EEPROM is present in the system. At all
rising CLK edges during the assertion of the
RST
pin,
the Am79C974 controller will sample the value of the
EESK/
LED1
pin. If the sampled value is a ONE, then the
Am79C974 controller assumes that an EEPROM is pre-
sent, and the EEPROM read operation begins shortly
after the
RST
pin is deasserted. If the sampled value of
EESK/
LED1
is a ZERO, then the Am79C974 controller
assumes that an external pulldown device is holding the
EESK/
LED1
pin low, and therefore, there is no
EEPROM in the system. Note that if the designer cre-
ates a system that contains an LED circuit on the
EESK/
LED1
pin but has no EEPROM present, then the
EEPROM auto-detection function will incorrectly con-
clude that an EEPROM is present in the system. How-
ever, this will not pose a problem for the Am79C974
controller, since it will recognize the lack of an EEPROM
at the end of the read operation, when the checksum
verification fails.
Systems Without an EEPROM
Some systems may be able to save the cost of an
EEPROM by storing the ISO 8802-3 (IEEE/ANSI 802.3)
station address and other configuration information
somewhere else in the system. There are several de-
sign choices:
If the LED1 is not needed in the system, then the sys-
tem designer may connect the EESK/
LED1
pin to a
resistive pulldown device. This will indicate to the
EEPROM auto-detection function that no EEPROM
is present.
If the LED1 function is needed in the system, then the
system designer will connect the EESK/
LED1
pin to
a resistive pullup device and the EEPROM auto-de-
tection function will incorrectly conclude that an
EEPROM is present in the system. However, this will
not pose a problem for the Am79C974 controller,
since it will recognize the lack of an EEPROM at the
end of the read operation, when the checksum verifi-
cation fails.
In either case, following the PCI configuration, addi-
tional information, including the ISO 8802-3 (IEEE/ANSI
802.3) station address, may be loaded into the
Am79C974 controller. Note that the IESRWE bit (bit 8 of
BCR2) must be set before the Am79C974 controller will
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C974KCW | PCnetTM-SCSI Combination Ethernet and SCSI Controller for PCI Systems |
| AM79C975 | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
| AM79C973 | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
| AM79C973KCW | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
| AM79C975KCW | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C974KC | 制造商:Advanced Micro Devices 功能描述: |
| AM79C974KC/W | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Node Controller |
| AM79C974KCW | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:PCnetTM-SCSI Combination Ethernet and SCSI Controller for PCI Systems |
| AM79C975 | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
發布緊急采購，3分鐘左右您將得到回復。