- 您現在的位置：買賣IC網 > PDF目錄375996 > GE28F640W30B85 EEPROM|FLASH|4MX16|CMOS|BGA|56PIN|PLASTIC PDF資料下載
參數資料
| 型號： | GE28F640W30B85 |
| 英文描述： | EEPROM|FLASH|4MX16|CMOS|BGA|56PIN|PLASTIC |
| 中文描述： | 的EEPROM | FLASH動畫| 4MX16 |的CMOS | BGA封裝| 56PIN |塑料 |
| 文件頁數： | 18/91頁 |
| 文件大?。?/td> | 994K |
| 代理商： | GE28F640W30B85 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁
1.8 Volt Intel
Wireless Flash Memory with 3 Volt I/O
18
Datasheet
Program
40h
Word Program
Setup
This preferred program command’s first cycle prepares the CUI for a program
operation. The second cycle latches address and data, and executes the WSM
program algorithm at this location. Status register updates occur when CE# or
OE# is toggled. A Read Array command is required to read array data after
programming.
10h
Alternate
Setup
Equivalent to a Program Setup command (40h).
30h
EFP Setup
This program command activates EFP mode. The first write cycle sets up the
command. If the second cycle is an EFP Confirm command (D0h), subsequent
writes provide program data. All other commands are ignored after EFP mode
begins.
D0h
EFP Confirm
If the first command was EFP Setup (30h), the CUI latches the address and data,
and prepares the device for EFP mode.
Erase
20h
Erase Setup
This command prepares the CUI for Block Erase. The device erases the block
addressed by the Erase Confirm command. If the next command is not Erase
Confirm, the CUI sets status register bits SR[5:4] to indicate command sequence
error and places the partition in the read status register mode.
D0h
Erase Confirm
If the first command was Erase Setup (20h), the CUI latches address and data,
and erases the block indicated by the erase confirm cycle address. During
program or erase, the partition responds only to Read Status Register, Program
Suspend, and Erase Suspend commands. CE# or OE# toggle updates status
register data.
Suspend
B0h
Program
Suspend or
Erase
Suspend
This command, issued at any device address, suspends the currently executing
program or erase operation. Status register data indicates the operation was
successfully suspended if SR[2] (program suspend) or SR[6] (erase suspend) and
SR[7] are set. The WSM remains in the suspended state regardless of control
signal states (except RST#).
D0h
Suspend
Resume
This command, issued at any device address, resumes the suspended program or
erase operation.
Block Locking
60h
Lock Setup
This command prepares the CUI lock configuration. If the next command is not
Lock Block, Unlock Block, or Lock-Down, the CUI sets SR[5:4] to indicate
command sequence error.
01h
Lock Block
If the previous command was Lock Setup (60h), the CUI locks the addressed
block.
D0h
Unlock Block
If the previous command was Lock Setup (60h), the CUI latches the address and
unlocks the addressed block. If previously locked-down, the operation has no
effect.
2Fh
Lock-Down
If the previous command was Lock Setup (60h), the CUI latches the address and
locks-down the addressed block.
Protection
C0h
Protection
Program
Setup
This command prepares the CUI for a protection register program operation. The
second cycle latches address and data, and starts the WSM’s protection register
program or lock algorithm. Toggling CE# or OE# updates the flash status register
data. To read array data after programming, issue a Read Array command.
Configuration
60h
Configuration
Setup
This command prepares the CUI for device configuration. If Set Configuration
Register is not the next command, the CUI sets SR[5:4] to indicate command
sequence error.
03h
Set
Configuration
Register
If the previous command was Configuration Setup (60h), the CUI latches the
address and writes the data from A[15:0] into the configuration register.
Subsequent read operations access array data.
NOTE:
Do not use unassigned commands. Intel reserves the right to redefine these codes for future functions.
Table 5.
Command Codes and Descriptions (Sheet 2 of 2)
Operation
Code
Device
Command
Description
相關PDF資料 |
PDF描述 |
|---|---|
| GE28F640W30T70 | EEPROM|FLASH|4MX16|CMOS|BGA|56PIN|PLASTIC |
| GE28F640W30T85 | EEPROM|FLASH|4MX16|CMOS|BGA|56PIN|PLASTIC |
| GF4435 | TRANSISTOR | MOSFET | P-CHANNEL | 30V V(BR)DSS | 8A I(D) | SO |
| GF4450 | TRANSISTOR | MOSFET | N-CHANNEL | 60V V(BR)DSS | 7.5A I(D) | SO |
| GF4800 | TRANSISTOR | MOSFET | N-CHANNEL | 30V V(BR)DSS | 9A I(D) | SO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GE28F640W30T70 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM|FLASH|4MX16|CMOS|BGA|56PIN|PLASTIC |
| GE28F640W30T85 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM|FLASH|4MX16|CMOS|BGA|56PIN|PLASTIC |
| GE28F800B3BA90 | 制造商:Intel 功能描述:NOR Flash, 512K x 16, 45 Pin, Plastic, BGA |
| GE28F800B3TA90 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:3 Volt Advanced Boot Block Flash Memory |
| GE28F800C3BA70 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced+ Boot Block Flash Memory (C3) |
發布緊急采購，3分鐘左右您將得到回復。