- 您現在的位置：買賣IC網 > PDF目錄360744 > ICS1892 10Base-T/100Base-TX Integrated PHYceiver PDF資料下載
參數資料
| 型號： | ICS1892 |
| 英文描述： | 10Base-T/100Base-TX Integrated PHYceiver |
| 文件頁數： | 37/148頁 |
| 文件大小： | 816K |
| 代理商： | ICS1892 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁
Chapter 7
Functional Blocks
ICS1892, Rev. D, 2/26/01
February 26, 2001
37
ICS1892
2000-2001, Integrated Circuit Systems, Inc.
All rights reserved.
7.2.2
Auto-Negotiation: Parallel Detection
The ICS1892 supports parallel detection. It is therefore compatible with networks that do not support the
auto-negotiation process. When enabled, the Auto-Negotiation sublayer can detect legacy 10Base-T link
partners as well as 100Base-TX link partners that do not have an auto-negotiation capability.
The Auto-Negotiation sublayer performs this parallel detection function when it does not get a response to
its FLP bursts. In these situations, the Auto-Negotiation sublayer performs the following steps:
1.
It sets the LP_AutoNeg_Able bit (bit 6.0) to logic zero, thereby identifying the remote link partner as not
being capable of executing the auto-negotiation process.
It sets the bit in the Auto-Negotiation Link Partner Abilities Register that corresponds to the 'parallel
detected' technology [for example, half-duplex, 10Base-T (bit 5.5) or half-duplex, 100Base-TX (bit
5.7)]. IEEE specification allows only half-duplex operation with auto-negotiation paralled detect
partners.
It sets the Status Register’s Auto-Negotiation Complete bit (bit 1.5) to logic one, indicating completion
of the auto-negotiation process.
It enables the detected link technology and disables the unused technologies.
2.
3.
4.
A remote link partner that does not support the auto-negotiation process does not respond to the
transmitted FLP bursts. The ICS1892 detects this situation and responds according to the data it receives.
The ICS1892 can receive one of five potential responses to the FLP bursts it is transmitting: FLP bursts,
10Base-T link pulses (that is, Normal Link Pulses), scrambled 100Base IDLEs, nothing, or a combination of
signal types.
A 10Base-T link partner transmits only Normal Link Pulses when idle. When the ICS1892 receives Normal
Link Pulses, it concludes that the remote link partner is a device that can use only 10Base-T technology. A
100Base-TX node without an Auto-Negotiation sublayer transmits 100M scrambled IDLE symbols in
response to the FLP bursts. Upon receipt of the scrambled IDLEs, the ICS1892 concludes that its remote
link partner is a 100Base-TX node that does not support the auto-negotiation process. For both 10Base-T
and 100Base-TX nodes without an Auto-Negotiation sublayer, the ICS1892 clears bit 6.0 to logic zero,
indicating that the link partner cannot perform the auto-negotiation process.
If the remote link partner responds to the FLP bursts with FLP bursts, then the link partner is a 100Base-TX
node that can support the auto-negotiation process. In this case, the ICS1892 sets to logic one the
Auto-Negotiation Expansion Register’s Link Partner Auto-Negotiation Ability bit (bit 6.0).
If the Auto-Negotiation sublayer does not receive any signal when monitoring the receive channel, then the
QuickPoll Detailed Status Register’s Signal Detect bit (bit 17.3) is set to logic one, indicating that no signal
is present.
Another possibility is that the ICS1892 senses that it is receiving multiple technology indications. In this
situation, the ICS1892 cannot determine which technology to enable. It informs the STA of this problem by
setting to logic one the Auto-Negotiation Expansion Register’s Parallel Detection Fault bit (bit 6.4).
7.2.3
Auto-Negotiation: Remote Fault Signaling
If the remote link partner detects a fault, the ICS1892 reports the remotely detected fault to the STA by
setting to logic one the Remote Fault Detected bit(s), 1.4, 5.13, and 17.1. The reception of a remote link
fault during the technology exchange also indicates that the remote link partner can perform remote fault
detection and the Remote Fault bit (bit 19.13) is set to logic one. In general, the reception of a remote fault
means that the remote link partner has a problem with the integrity of its receive channel.
Similarly, if the ICS1892 detects a link fault, it transmits a remote fault-detected condition to its remote link
partner. In this situation, the ICS1892 sets to logic one the Auto-Negotiation Link Partner Ability Register’s
Remote Fault Indication bit (bit 5.13). In addition, the ICS1892 sets to logic one the Extended Control
Register’s bit 19.13, indicating that it sent a remote fault to its remote link partner.
相關PDF資料 |
PDF描述 |
|---|---|
| ICS1892Y | 10Base-T/100Base-TX Integrated PHYceiver |
| ICS1892Y-10 | 10Base-T/100Base-TX Integrated PHYceiver |
| ICS1892Y-14 | 10Base-T/100Base-TX Integrated PHYceiver |
| ICS1893AF | 3.3V 10Base-T/100Base-TX Integrated PHYceiverTM |
| ICS1893Y-10 | 3.3V 10Base-T/100Base-TX Integrated PHYceiverTM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS1892Y | 制造商:ICS 制造商全稱:ICS 功能描述:10Base-T/100Base-TX Integrated PHYceiver |
| ICS1892Y-10 | 制造商:ICS 制造商全稱:ICS 功能描述:10Base-T/100Base-TX Integrated PHYceiver |
| ICS1892Y-14 | 制造商:ICS 制造商全稱:ICS 功能描述:10Base-T/100Base-TX Integrated PHYceiver |
| ICS1893 | 制造商:ICS 制造商全稱:ICS 功能描述:3.3-V 10Base-T/100Base-TX Integrated PHYceiver |
| ICS1893_09 | 制造商:ICS 制造商全稱:ICS 功能描述:3.3-V 10Base-T/100Base-TX Integrated PHYceiver? |
發布緊急采購，3分鐘左右您將得到回復。