- 您現在的位置：買賣IC網 > PDF目錄224506 > MT48LC32M4A2P-7ELIT:G 32M X 4 SYNCHRONOUS DRAM, 5.4 ns, PDSO54 PDF資料下載
參數資料
| 型號： | MT48LC32M4A2P-7ELIT:G |
| 元件分類： | DRAM |
| 英文描述： | 32M X 4 SYNCHRONOUS DRAM, 5.4 ns, PDSO54 |
| 封裝： | 0.400 INCH, LEAD FREE, PLASTIC, TSOP2-54 |
| 文件頁數： | 17/74頁 |
| 文件大?。?/td> | 2385K |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
PDF: 09005aef8091e66d/Source: 09005aef8091e625
Micron Technology, Inc., reserves the right to change products or specifications without notice.
128MSDRAM_2.fm - Rev. N 1/09 EN
24
1999 Micron Technology, Inc. All rights reserved.
128Mb: x4, x8, x16 SDRAM
Operations
The procedure for exiting self refresh requires a sequence of commands. First, CLK must
be stable (stable clock is defined as a signal cycling within timing constraints specified
for the clock pin) prior to CKE going back HIGH. After CKE is HIGH, the SDRAM must
have NOP commands issued (a minimum of 2 clocks) for tXSR because this amount of
time is required for the completion of any internal refresh in progress.
Upon exiting the self refresh mode, AUTO REFRESH commands must be issued every
15.625s or less because both SELF REFRESH and AUTO REFRESH utilize the row
refresh counter.
Self refresh is not supported on automotive temperature (AT) devices.
Operations
Bank/row Activation
Before any READ or WRITE commands can be issued to a bank within the SDRAM, a row
in that bank must be “opened.” This is accomplished via the ACTIVE command, which
selects both the bank and the row to be activated (see Figure 9 on page 25).
After opening a row (issuing an ACTIVE command), a READ or WRITE command may be
issued to that row, subject to the tRCD specification. tRCD (MIN) should be divided by
the clock period and rounded up to the next whole number to determine the earliest
clock edge after the ACTIVE command on which a READ or WRITE command can be
entered. For example, a tRCD specification of 20ns with a 125 MHz clock (8ns period)
results in 2.5 clocks, rounded to 3. This is reflected in Figure 10 on page 25, which covers
any case where 2 < tRCD (MIN)/tCK ≤ 3. (The same procedure is used to convert other
specification limits from time units to clock cycles.)
A subsequent ACTIVE command to a different row in the same bank can only be issued
after the previous active row has been “closed” (precharged). The minimum time
interval between successive ACTIVE commands to the same bank is defined by tRC.
A subsequent ACTIVE command to another bank can be issued while the first bank is
being accessed, which results in a reduction of total row-access overhead. The minimum
time interval between successive ACTIVE commands to different banks is defined by
tRRD.
相關PDF資料 |
PDF描述 |
|---|---|
| MT55L256L18FT-12TR | 256K X 18 ZBT SRAM, 9 ns, PQFP100 |
| MT55L256L32FT-12 | 256K X 32 ZBT SRAM, 9 ns, PQFP100 |
| MT55L512V18PF-6 | 512K X 18 ZBT SRAM, 3.5 ns, PBGA165 |
| MT57W4MH9CF-6 | 4M X 9 DDR SRAM, 0.5 ns, PBGA165 |
| MT58L128L36D1T-5IT | 128K X 36 STANDARD SRAM, 2.8 ns, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT48LC32M4A2TG | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:SYNCHRONOUS DRAM |
| MT48LC32M4A2TG-75 | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:SYNCHRONOUS DRAM |
| MT48LC32M4A2TG-75IT | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:SYNCHRONOUS DRAM |
發布緊急采購，3分鐘左右您將得到回復。