參數資料
型號： XRT86VL3X
廠商： Exar Corporation
元件分類： 通信及網絡
英文描述： Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
中文描述： Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
文件頁數： 55/149頁
文件大?。?/td> 1274K
代理商： XRT86VL3X
XRT86VL3X
48
REV. 1.2.0
T1/E1/J1 FRAMER/LIU COMBO - ARCHITECTURE DESCRIPTION
4.3.2
DMO (Digital Monitor Output)
The driver monitor circuit is used to detect transmit driver failures by monitoring the activities at TTIP/TRING
outputs. Driver failure may be caused by a short circuit in the primary transformer or system problems at the
transmit inputs. If the transmitter of a channel has no output for more than 128 clock cycles, DMO goes "High"
until a valid transmit pulse is detected. If the DMO interrupt is enabled, the change in status of DMO will cause
the interrupt pin to go "Low". Once the status register is read, the interrupt pin will return "High" and the status
register will be reset (RUR).
4.3.3
Transmit Jitter Attenuator
The transmit path has a dedicated jitter attenuator to reduce phase and frequency jitter in the transmit clock.
The jitter attenuator uses a data FIFO (First In First Out) with a programmable depth of 32-bit or 64-bit. When
the Read and Write pointers of the FIFO are within 2-Bits of over-flowing or under-flowing, the bandwidth of the
jitter attenuator is widened to track the short term input jitter, thereby avoiding data corruption. When this
condition occurs, the jitter attenuator will not attenuate input jitter until the Read/Write pointer’s position is
outside the 2-Bit window. In T1 mode, the bandwidth of the JA is always set to 3Hz. In E1 mode, the
bandwidth is programmable to either 10Hz or 1.5Hz (1.5Hz automatically selects the 64-Bit FIFO depth). The
JA has a clock delay equal to of the FIFO bit depth.
N
OTE
:
The Receive Path has a dedicated jitter attenuator. See the Receive Path Line Interface Section.
4.4
Line Termination (TTIP/TRING)
The output stage of the transmit path generates standard return-to-zero (RZ) signals to the line interface for T1/
E1/J1 twisted pair or E1 coaxial cable. The physical interface is optimized by placing the terminating
impedance inside the LIU. This allows one bill of materials for all modes of operation reducing the number of
external components necessary in system design. The transmitter outputs only require one DC blocking
capacitor of 0.68
μ
F. For redundancy applications (or simply to tri-state the transmitters), set TxTSEL to a "1" in
the appropriate channel register. A typical transmit interface is shown in
Figure 50
.
F
IGURE
50. T
YPICAL
C
ONNECTION
D
IAGRAM
U
SING
I
NTERNAL
T
ERMINATION
T
TIP
T
RING
XRT86VL3x LIU
1:2
Internal Impedance
Line Interface T1/E1/J1
C=0.68uF
One Bill of Materials
Transmitter
Output
相關PDF資料
PDF描述
XRT91L30_0611 STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER
XRT91L306 STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER
XRT91L30IQ STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER
XRT91L30 STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER
XRT91L31 STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER
相關代理商/技術參數
參數描述
XRT86VL3X_07 制造商:EXAR 制造商全稱:EXAR 功能描述:T1/E1/J1 FRAMER/LIU COMBO - ARCHITECTURE DESCRIPTION
XRT86VL3X_0710 制造商:EXAR 制造商全稱:EXAR 功能描述:T1/E1/J1 FRAMER/LIU COMBO - ARCHITECTURE DESCRIPTION
XRT86VX38 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER/LIU COMBO - HARDWARE DESCRIPTION
XRT86VX38_09 制造商:EXAR 制造商全稱:EXAR 功能描述:8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION
XRT86VX38_0906 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER/LIU COMBO - HARDWARE DESCRIPTION
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*