參數資料
型號： XRT86VL3X
廠商： Exar Corporation
元件分類： 通信及網絡
英文描述： Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
中文描述： Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
文件頁數： 59/149頁
文件大?。?/td> 1274K
代理商： XRT86VL3X
XRT86VL3X
52
REV. 1.2.0
T1/E1/J1 FRAMER/LIU COMBO - ARCHITECTURE DESCRIPTION
5.2.3
FLSD (FIFO Limit Status Detection)
The purpose of the FIFO limit status is to indicate when the Read and Write FIFO pointers are within a pre-
determined range (over-flow or under-flow indication). The FLSD is set to "1" if the FIFO Read and Write
Pointers are within ±3-Bits.
5.2.4
Receive Jitter Attenuator
The receive path has a dedicated jitter attenuator to reduce phase and frequency jitter in the recovered clock.
The jitter attenuator uses a data FIFO (First In First Out) with a programmable depth of 32-bit or 64-bit. If the
LIU is used for line synchronization (loop timing systems), the JA should be enabled in the receive path. When
the Read and Write pointers of the FIFO are within 2-Bits of over-flowing or under-flowing, the bandwidth of the
jitter attenuator is widened to track the short term input jitter, thereby avoiding data corruption. When this
condition occurs, the jitter attenuator will not attenuate input jitter until the Read/Write pointer’s position is
outside the 2-Bit window. In T1 mode, the bandwidth of the JA is always set to 3Hz. In E1 mode, the
bandwidth is programmable to either 10Hz or 1.5Hz (1.5Hz automatically selects the 64-Bit FIFO depth). The
JA has a clock delay equal to of the FIFO bit depth.
N
OTE
:
The Transmit Path has a dedicated jitter attenuator. See the Transmit Path Line Interface Section.
5.2.5
RxMUTE (Receiver LOS with Data Muting)
The receive muting function can be selected by setting RxMUTE to "1" in the appropriate global register. If
selected, any channel that experiences an RLOS condition will automatically pull the output of the LIU section
"Low" to prevent data chattering. If RLOS does not occur, the RxMUTE will remain inactive until an RLOS on a
given channel occurs. The default setting for RxMUTE is "0" which is disabled. A simplified block diagram of
the RxMUTE function is shown in
Figure 56
.
F
IGURE
55. P
ROCESS
B
LOCK
FOR
A
UTOMATIC
L
OOP
C
ODE
D
ETECTION
Automatic Remote
Loopback
Loop-Up
Code for
5 sec
Yes
No
Loop-Down
Code for
5 sec
No
Yes
Disable Remote
Loopback
相關PDF資料
PDF描述
XRT91L30_0611 STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER
XRT91L306 STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER
XRT91L30IQ STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER
XRT91L30 STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER
XRT91L31 STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER
相關代理商/技術參數
參數描述
XRT86VL3X_07 制造商:EXAR 制造商全稱:EXAR 功能描述:T1/E1/J1 FRAMER/LIU COMBO - ARCHITECTURE DESCRIPTION
XRT86VL3X_0710 制造商:EXAR 制造商全稱:EXAR 功能描述:T1/E1/J1 FRAMER/LIU COMBO - ARCHITECTURE DESCRIPTION
XRT86VX38 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER/LIU COMBO - HARDWARE DESCRIPTION
XRT86VX38_09 制造商:EXAR 制造商全稱:EXAR 功能描述:8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION
XRT86VX38_0906 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER/LIU COMBO - HARDWARE DESCRIPTION
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*