- 您現在的位置：買賣IC網 > PDF目錄224506 > MT47H128M8HQ-187ELAT:E 128M X 8 DDR DRAM, 0.35 ns, PBGA60 PDF資料下載
參數資料
| 型號： | MT47H128M8HQ-187ELAT:E |
| 元件分類： | DRAM |
| 英文描述： | 128M X 8 DDR DRAM, 0.35 ns, PBGA60 |
| 封裝： | 8 X 11.50 MM, ROHS COMPLIANT, FBGA-60 |
| 文件頁數： | 69/133頁 |
| 文件大小： | 9170K |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁當前第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁
18. The inputs to the DRAM must be aligned to the associated clock, that is, the actual clock
that latches it in. However, the input timing (in ns) references to the tCK (AVG) when
determining the required number of clocks. The following input parameters are deter-
mined by taking the specified percentage times the tCK (AVG) rather than tCK: tIPW,
tDIPW, tDQSS, tDQSH, tDQSL, tDSS, tDSH, tWPST, and tWPRE.
19. The DRAM output timing is aligned to the nominal or average clock. Most output param-
eters must be derated by the actual jitter error when input clock jitter is present; this
will result in each parameter becoming larger. The following parameters are required to
be derated by subtracting tERR5per (MAX): tAC (MIN), tDQSCK (MIN), tLZDQS (MIN), tLZDQ
(MIN), tAON (MIN); while the following parameters are required to be derated by sub-
tracting tERR5per (MIN): tAC (MAX), tDQSCK (MAX), tHZ (MAX), tLZDQS (MAX), tLZDQ
(MAX), tAON (MAX). The parameter tRPRE (MIN) is derated by subtracting tJITper (MAX),
while tRPRE (MAX), is derated by subtracting tJITper (MIN). The parameter tRPST (MIN) is
derated by subtracting tJITdty (MAX), while tRPST (MAX), is derated by subtracting tJITd-
ty (MIN). Output timings that require tERR5per derating can be observed to have offsets
relative to the clock; however, the total window will not degrade.
20. When DQS is used single-ended, the minimum limit is reduced by 100ps.
21. tHZ and tLZ transitions occur in the same access time windows as valid data transitions.
These parameters are not referenced to a specific voltage level, but specify when the
device output is no longer driving (tHZ) or begins driving (tLZ).
22. tLZ (MIN) will prevail over a tDQSCK (MIN) + tRPRE (MAX) condition.
23. This is not a device limit. The device will operate with a negative value, but system per-
formance could be degraded due to bus turnaround.
24. It is recommended that DQS be valid (HIGH or LOW) on or before the WRITE command.
The case shown (DQS going from High-Z to logic LOW) applies when no WRITEs were
previously in progress on the bus. If a previous WRITE was in progress, DQS could be
HIGH during this time, depending on tDQSS.
25. The intent of the “Don’t Care” state after completion of the postamble is that the DQS-
driven signal should either be HIGH, LOW, or High-Z, and that any signal transition
within the input switching region must follow valid input requirements. That is, if DQS
transitions HIGH (above VIH[DC]min), then it must not transition LOW (below VIH[DC]) prior
to tDQSH (MIN).
26. Referenced to each output group: x4 = DQS with DQ0–DQ3; x8 = DQS with DQ0–DQ7;
x16 = LDQS with DQ0–DQ7; and UDQS with DQ8–DQ15.
27. The data valid window is derived by achieving other specifications: tHP (tCK/2), tDQSQ,
and tQH (tQH = tHP - tQHS). The data valid window derates in direct proportion to the
clock duty cycle and a practical data valid window can be derived.
28. tQH = tHP - tQHS; the worst case tQH would be the lesser of tCL (ABS) MAX or
tCH (ABS) MAX times tCK (ABS) MIN - tQHS. Minimizing the amount of tCH (AVG) offset
and value of tJITdty will provide a larger tQH, which in turn will provide a larger valid
data out window.
29. This maximum value is derived from the referenced test load. tHZ (MAX) will prevail
over tDQSCK (MAX) + tRPST (MAX) condition.
30. The values listed are for the differential DQS strobe (DQS and DQS#) with a differential
slew rate of 2 V/ns (1 V/ns for each signal). There are two sets of values listed: tDSa, tDHa
and tDSb, tDHb. The tDSa, tDHa values (for reference only) are equivalent to the baseline
values of tDSb, tDHb at VREF when the slew rate is 2 V/ns, differentially. The baseline val-
ues, tDSb, tDHb, are the JEDEC-defined values, referenced from the logic trip points. tDSb
is referenced from VIH(AC) for a rising signal and VIL(AC) for a falling signal, while tDHb is
referenced from VIL(DC) for a rising signal and VIH(DC) for a falling signal. If the differen-
tial DQS slew rate is not equal to 2 V/ns, then the baseline values must be derated by
adding the values from Table 30 (page 61) and Table 31 (page 62). If the DQS differ-
ential strobe feature is not enabled, then the DQS strobe is single-ended and the
baseline values must be derated using Table 32 (page 63). Single-ended DQS data tim-
ing is referenced at DQS crossing VREF. The correct timing values for a single-ended DQS
1Gb: x4, x8, x16 DDR2 SDRAM
AC Timing Operating Specifications
PDF: 09005aef821ae8bf
1GbDDR2.pdf – Rev. S 10/09 EN
40
Micron Technology, Inc. reserves the right to change products or specifications without notice.
2004 Micron Technology, Inc. All rights reserved.
相關PDF資料 |
PDF描述 |
|---|---|
| MT48LC2M32B1TG-7 | 2M X 32 SYNCHRONOUS DRAM, 5.5 ns, PDSO86 |
| MT48LC32M4A2P-7ELIT:G | 32M X 4 SYNCHRONOUS DRAM, 5.4 ns, PDSO54 |
| MT55L256L18FT-12TR | 256K X 18 ZBT SRAM, 9 ns, PQFP100 |
| MT55L256L32FT-12 | 256K X 32 ZBT SRAM, 9 ns, PQFP100 |
| MT55L512V18PF-6 | 512K X 18 ZBT SRAM, 3.5 ns, PBGA165 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT47H128M8HQ-25AT | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:DDR2 SDRAM |
| MT47H128M8HQ-25EAT | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:DDR2 SDRAM |
發布緊急采購，3分鐘左右您將得到回復。