- 您現在的位置：買賣IC網 > PDF目錄371776 > HC805P18GRS 68HC805P18 Technical Data PDF資料下載
參數資料
| 型號： | HC805P18GRS |
| 英文描述： | 68HC805P18 Technical Data |
| 中文描述： | 68HC805P18技術數據 |
| 文件頁數： | 28/111頁 |
| 文件大?。?/td> | 748K |
| 代理商： | HC805P18GRS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁
GENERAL RELEASE SPECIFICATION
MC68HC805P18
Rev. 1.0
INTERRUPTS
MOTOROLA
4-1
8
2
3
4
5
6
7
8
9
10
11
12
13
14
A
16
17
18
19
20
SECTION 4
INTERRUPTS
4.1 Introduction
The MCU can be interrupted six different ways:
Non-maskable software interrupt instruction (SWI)
External asynchronous interrupt (IRQ)
Input capture interrupt (TIMER)
Output compare interrupt (TIMER)
Timer overflow interrupt (TIMER)
Port A interrupt (if selected via MOR2, bits 0 through 7).
Interrupts cause the processor to save the register contents on the stack and to set
the interrupt mask (I bit) to prevent additional interrupts. Unlike reset, hardware
interrupts do not cause the current instruction execution to be halted, but are
considered pending until the current instruction is completed.
When the current instruction is completed, the processor checks all pending
hardware interrupts. If interrupts are not masked (I bit in the condition code register
is clear) and the corresponding interrupt enable bit is set, the processor proceeds
with interrupt processing. Otherwise, the next instruction is fetched and executed.
The SWI is executed the same as any other instruction, regardless of the I bit state.
When an interrupt is to be processed, the CPU puts the register contents on the
stack, sets the I bit in the CCR, and fetches the address of the corresponding
interrupt service routine from the vector table at locations $3FF0 through $3FFF. If
more than one interrupt is pending when the interrupt vector is fetched, the
interrupt with the highest vector location shown in Table 4-1 will be serviced first.
An RTI instruction is used to signify when the interrupt software service routine is
completed. The RTI instruction causes the CPU state to be recovered from the
stack and normal processing to resume at the next instruction that was to be
executed when the interrupt took place. Figure 4-1 shows the sequence of events
that occurs during interrupt processing.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| HC820 | Low power audio power amplifier |
| HC9-55564-5 | RF Modulator |
| HC908AT32GRS | 68HC908AT32 General Release Specification |
| HC908JB16AD | Addendum to MC68HC908JB16 Technical Data Rev. 1.0 |
| HC908JB8AD | Addendum to MC68HC908JB8 Technical Data Rev. 2.0 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HC80-8.0MHZ | 功能描述:晶體 CRYSTAL 8MHz RoHS:否 制造商:AVX 頻率:26 MHz 容差: 頻率穩定性:50 PPM 負載電容:8 pF 端接類型:SMD/SMT 封裝 / 箱體:1210 (3225 metric) 工作溫度范圍:- 40 C to + 150 C 尺寸:2.5 mm W x 3.2 mm L x 0.85 mm H 封裝:Reel |
| HC80U | 制造商:FOX 制造商全稱:FOX 功能描述:RESISTANCE WELD THRU-HOLE CRYSTAL |
| HC80U-3.6864MHz | 功能描述:晶體 3.6864MHz 20pF RoHS:否 制造商:AVX 頻率:26 MHz 容差: 頻率穩定性:50 PPM 負載電容:8 pF 端接類型:SMD/SMT 封裝 / 箱體:1210 (3225 metric) 工作溫度范圍:- 40 C to + 150 C 尺寸:2.5 mm W x 3.2 mm L x 0.85 mm H 封裝:Reel |
| HC80UW | 制造商:FOX 制造商全稱:FOX 功能描述:RESISTANCE WELD MINIATURE CRYSTAL (GULLWING) |
| HC8-100-R | 功能描述:固定電感器 10uH 9.2A 43.6mOhms RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
發布緊急采購，3分鐘左右您將得到回復。