參數資料
型號： LXT970A
廠商： Intel Corp.
英文描述： Dual-Speed Fast Ethernet Transceiver
中文描述： 雙速度快速以太網收發器
文件頁數： 19/74頁
文件大?。?/td> 1061K
代理商： LXT970A
Dual-Speed Fast Ethernet Transceiver
—
LXT970A
Datasheet
19
2.2
Interfaces (Network Media/Protocol Support)
The LXT970A provides the following interfaces:
A Twisted-Pair Interface which directly supports 100BASE-TX and 10BASE-T applications.
A pseudo-ECL (PECL) Fiber Interface which supports 100BASE-FX applications through an
external fiber transceiver.
An MII (Media Independent Interface) for interfacing 10/100 Media Access Controllers
(MACs).
A Hardware Control Interface to configure various operating characteristics.
2.2.1
Twisted-Pair Interface
The Twisted-Pair Interface directly supports both 100BASE-TX and 10BASE-T applications. The
interface is capable of directly driving an RJ-45 interface through magnetics and termination
resistors. The interface uses two signal pairs - one for transmit and one for receive. A third output,
TREF, connects to the center-tap of the transmit transformer. The same signal pairs, magnetics, and
termination resistors are used for both 10 and 100 Mbps operation.
When the LXT970A is operating as a 100 Mbps device, it transmits and receives a 125 Mbps, 5B-
encoded, scrambled MLT-3 waveform on this interface. The MLT-3 waveform is continuous.
When there is no data to send,
“
IDLE
”
symbols are sent and received.
When the LXT970A is operating as a 10 Mbps device, it transmits and receives 10 Mbps
Manchester-encoded data. The waveform is not continuous. When there is no data to send, the
line is left in an idle state. Link pulses are transmitted periodically to keep the link up.
The LXT970A supports both fixed operation and auto-negotiation with parallel detection on this
interface. Fixed operation allows the designer to specify the line speed and duplex mode. With
auto-negotiation enabled, the LXT970A automatically determines line speed and duplex state by
exchanging capability
“
pages
”
with its link partner.
A 4 k
passive load is always present across the twisted-pair inputs. When enabled, the twisted-
pair inputs are actively biased to approximately 2.8V.
In applications where the Twisted-Pair Interface is not used, the inputs and outputs may be left
unconnected.
The Twisted-Pair Interface is disabled in power down mode, when the Fiber Interface is selected,
or when the transmit disconnect (bit 19.0) is set. When the Twisted-Pair Interface is disabled its
outputs are tri-stated and inputs are unbiased.
2.2.2
Fiber Interface
The pseudo-ECL Fiber Interface is suitable for driving 100BASE-FX applications through an
external fiber transceiver. This interface consists of a transmit and receive pair. The LXT970A
sends and receives a continuous 125 Mbps, 5B-encoded NRZI stream on this interface.
Scrambling and MLT-3 are not used in fiber connections.
There is no industry standard for auto-negotiation on 100BASE-FX. The LXT970A only supports
forced operation on the Fiber Interface. The LXT970A does not support 10FL (10 Mbps fiber)
applications.
相關PDF資料
PDF描述
LXT970 Fast Ethernet Transceiver
LXT970QC Fast Ethernet Transceiver
LXT971A 3.3V Dual-Speed Fast Ethernet PHY Transceiver
LXT972A 3.3V Dual-Speed Fast Ethernet Transceiver Datasheet
LXT972ALC 3.3V Dual-Speed Fast Ethernet Transceiver Datasheet
相關代理商/技術參數
參數描述
LXT970AQC 制造商:LEVEL ONE 功能描述: 制造商:LEVELONE 功能描述: 制造商: 功能描述: 制造商:LEVEL1 功能描述:
LXT970AQC.B11 制造商:Intel 功能描述:
LXT970ATC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecomm/Datacomm
LXT970QC 制造商:LEVEL ONE 功能描述: 制造商:Level One 功能描述:LAN Transceiver, Single, 64 Pin, Plastic, QFP 制造商:Level One Communications 功能描述:LAN Transceiver, Single, 64 Pin, Plastic, QFP
LXT971A 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:3.3V Dual-Speed Fast Ethernet PHY Transceiver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*