- 您現在的位置：買賣IC網 > PDF目錄359141 > MC68HC08KH12A (飛思卡爾半導體(中國)有限公司) Microcontrollers PDF資料下載
參數資料
| 型號： | MC68HC08KH12A |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Microcontrollers |
| 中文描述： | 微控制器 |
| 文件頁數： | 147/178頁 |
| 文件大小： | 925K |
| 代理商： | MC68HC08KH12A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁當前第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁
IRQ Module During Break Interrupts
MC68HC08KH12A Data Sheet, Rev. 1.1
Freescale Semiconductor
147
14.3.1 IRQ1 Pin
A logic zero on the IRQ1 pin can latch an interrupt request into the IRQ1 latch. A vector fetch, software
clear, or reset clears the IRQ1 latch.
If the MODE1 bit is set, the IRQ1 pin is both falling-edge-sensitive and low-level-sensitive. With MODE1
set, both of the following actions must occur to clear IRQ1:
Vector fetch or software clear — A vector fetch generates an interrupt acknowledge signal to clear
the latch. Software may generate the interrupt acknowledge signal by writing a logic one to the
ACK1 bit in the interrupt status and control register (ISCR). The ACK1 bit is useful in applications
that poll the IRQ1 pin and require software to clear the IRQ1 latch. Writing to the ACK1 bit prior to
leaving an interrupt service routine can also prevent spurious interrupts due to noise. Setting ACK1
does not affect subsequent transitions on the IRQ1 pin. A falling edge that occurs after writing to
the ACK1 bit latches another interrupt request. If the IRQ1 mask bit, IMASK1, is clear, the CPU
loads the program counter with the vector address at locations $FFFA and $FFFB.
Return of the IRQ1 pin to logic one — As long as the IRQ1 pin is at logic zero, IRQ1 remains active.
The vector fetch or software clear and the return of the IRQ1 pin to logic one may occur in any order. The
interrupt request remains pending as long as the IRQ1 pin is at logic zero. A reset will clear the latch and
the MODE1 control bit, thereby clearing the interrupt even if the pin stays low.
If the MODE1 bit is clear, the IRQ1 pin is falling-edge-sensitive only. With MODE1 clear, a vector fetch or
software clear immediately clears the IRQ1 latch.
The IRQF1 bit in the ISCR register can be used to check for pending interrupts. The IRQF1 bit is not
affected by the IMASK1 bit, which makes it useful in applications where polling is preferred.
Use the BIH or BIL instruction to read the logic level on the IRQ1 pin.
NOTE
When using the level-sensitive interrupt trigger, avoid false interrupts by
masking interrupt requests in the interrupt routine.
14.4 IRQ Module During Break Interrupts
The system integration module (SIM) controls whether the IRQ1 latch can be cleared during the break
state. The BCFE bit in the break flag control register (BFCR) enables software to clear the latches during
the break state. (See
Chapter 7 System Integration Module (SIM)
.)
To allow software to clear the IRQ1 latch during a break interrupt, write a logic one to the BCFE bit. If a
latch is cleared during the break state, it remains cleared when the MCU exits the break state.
To protect the latches during the break state, write a logic zero to the BCFE bit. With BCFE at logic zero
(its default state), writing to the ACK1 bit in the IRQ status and control register during the break state has
no effect on the IRQ latch.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC08LT8 | Microcontrollers |
| MC68HC08SR12 | M68HC08 Microcontrollers |
| MC68HC11E0 | HC11 Microcontrollers |
| MC68HC11K0 | HCMOS Microcontroller Unit |
| MC68HC11KMNPEVS | Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC08KL8B | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification |
| MC68HC08KL8FB | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification |
| MC68HC08KX8 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Microcontrollers |
| MC68HC08LJ12 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Addendum to MC68HC908LJ12 Technical Data |
| MC68HC08LJ12CFB | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Addendum to MC68HC908LJ12 Technical Data |
發布緊急采購，3分鐘左右您將得到回復。