- 您現在的位置：買賣IC網 > PDF目錄369945 > P8XC591 (NXP Semiconductors N.V.) HiRel FPGA, Low-Power 1.0?? CMOS Technology PDF資料下載
參數資料
| 型號： | P8XC591 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | HiRel FPGA, Low-Power 1.0?? CMOS Technology |
| 中文描述： | 單芯片8 - CAN控制器位微控制器 |
| 文件頁數： | 34/160頁 |
| 文件大?。?/td> | 601K |
| 代理商： | P8XC591 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁
2000 Jul 26
34
Philips Semiconductors
Preliminary Specification
Single-chip 8-bit microcontroller with CAN controller
P8xC591
12.5.2
M
ODE
R
EGISTER
(MOD)
The contents of the Mode Register are used to change the behaviour of the CAN controller. Bits may be set or reset by
the CPU that uses the Mode Register as a read / write memory. Reserved Bits are read as “0”.
Table 13
Mode Register (MOD) CAN Addr. 0 bit interpretation
Notes
1.
A write access to the bits MOD.1, MOD.2, MOD.5, MOD.6 and MOD.7 is possible only, if the Reset Mode is entered
previously.
The PeliCAN Block will enter Sleep Mode, if the Sleep Mode bit is set ‘1’ (sleep), there is no bus activity and no
interrupt is pending. Setting of SM with at least one of the previously mentioned exceptions valid will result in a
wake-up interrupt. The CAN controller will wake up if SM is set LOW (wake-up) or there is bus activity. On wake-up,
a Wake-up Interrupt is generated. A sleeping CAN controller which wakes up due to bus activity will not be able to
receive this message until it detects 11 consecutive recessive bits (Bus-Free sequence). Note that setting of SM is
not possible in Reset Mode. After clearing of Reset Mode, setting of SM is possible first, when Bus-Free is detected
again.
This mode of operation forces the CAN controller to be error passive. Message Transmission is not possible. The
Listen Only Mode can be used e.g. for software driven bit rate detection and “hot plugging”.
2.
3.
BIT
SYMBOL
NAME
VALUE
FUNCTION
MOD.7
TM
Test Mode;
Note 1
1 (activated)
The TXDC pin will reflect the bit, detected on RXDC pin, with
the next positive edge of the system clock. The RPM bit has
no influence within this mode.
0 (disabled)
1 (high active)
MOD.6
MOD.5
RIPM
RPM
Reserved.
Receive Polarity
Mode
RXD inputs are active high (dominant = 1).
0 (low active)
1 (high active))
RXD inputs are active low (dominant = 0).
The CAN controller enters Sleep Mode if no CAN interrupt is
pending and there is no bus activity.
MOD.4
SM
Sleep Mode;
Note 2
0 (low active)
1 (self test)
MOD.3
MOD.2
reserved
Self Test Mode;
Note 1
In this mode a full node test is possible without any other
active node on the bus using the Self Reception Request
command. The CAN controller will perform a successful
transmission, even if there is no acknowledge received.
An acknowledge is required for successful transmission.
In this mode the CAN would give no acknowledge to the
CAN bus, even if a message is received successfully. No
active error flags are driven to the bus. The error counters
are stopped at the current value.
Normal communication.
Setting the Reset Mode bit results in aborting the current
transmission/reception of a message and entering the Reset
Mode.
On the’1’-to-’0’ transition of the Reset Mode bit, the CAN
controller returns to the Operating Mode.
STM
0 (normal)
1 (reset)
MOD.1
LOM
Listen Only
Mode; Notes 1
and 3
0 (normal)
1 (reset)
MOD.0
RM
Reset Mode;
Note 4
0 (normal)
相關PDF資料 |
PDF描述 |
|---|---|
| P90CE201 | 16-bit microcontroller |
| P90CE201AEB | 16-bit microcontroller |
| P9217 | PbS photoconductive detector |
| P930 | CdS photoconductive cell |
| PA025XSB | This technical specification applies to 2.5inch color TFT-LCD panel. |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P8XC592 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with on-chip CAN |
| P8XCE598 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with on-chip CAN |
| P8XCL580HFH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low voltage 8-bit microcontrollers with UART, I2C-bus and ADC |
| P8XCL580HFT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low voltage 8-bit microcontrollers with UART, I2C-bus and ADC |
| P8Z77 DELUXE | 制造商:Asus 功能描述:P8Z77-V Deluxe ATX Motherboard |
發布緊急采購，3分鐘左右您將得到回復。