- 您現在的位置：買賣IC網 > PDF目錄371179 > T8100A H.100/H.110 Interface and Time-Slot Interchangers PDF資料下載
參數資料
| 型號： | T8100A |
| 英文描述： | H.100/H.110 Interface and Time-Slot Interchangers |
| 中文描述： | H.100/H.110接口和時隙Interchangers |
| 文件頁數： | 57/112頁 |
| 文件大?。?/td> | 1408K |
| 代理商： | T8100A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁當前第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁
Lucent Technologies Inc.
53
Advance Data Sheet
November 1999
H.100/H.110 Interfaces and Time-Slot Interchangers
Ambassador T8100A, T8102, and T8105
2 Architecture and Functional Description
(continued)
2.5 Clocking Section
(continued)
2.5.8 Clock Control Register Definitions
(continued)
Table 50. CKS: Clocks, Secondary (Fallback) Selection, 0x04
Clock register 0x04 is CKS, the secondary clock selection register. This is also referred to as fallback. When pro-
gramming the clock registers, writing to CKW and CKS should be programmed last. The register is defined as fol-
lows.
Reg
CKS
R/W
—
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
FF
Bit 2
Bit 1
FCSEL
Bit 0
FRS
FTS
Symbol
FRS
Bit
7—6 FRS provides an alternate clock resource selection. FRS forces the clock resource selector to
choose a new source for PLL #1.
FRS = 00,
External input (through the 4MHzIN pin).
FRS = 01,
Resource divider.
FRS = 10,
DPLL @ 2.048 MHz.
FRS = 11,
DPLL @ 4.096 MHz.
Note:
The decode is the same as that of the CRS bits (in the clock resource register, CKR).
5—4 FTS determines the basic fallback mode (see Section 2.5.8.1 Basic Fallback Mode).
FTS = 00,
This is automatic fallback to the oscillator divided by 4,
thus 4.096 MHz.
FTS = 01,
This disables fallback.
FTS = 10,
This is one of the two major fallback selections.
FTS = 11,
This fallback selection specifically supports standard H.100 and
H.110 applications.
3
FF forces the use of the FRS, FTS, and FCSEL. FF is used as a test of the fallback, but can
also be used as a software-initiated fallback.
FF = 0,
Normal operation.
FF = 1,
Force use of secondary (fallback) resources.
2—0 FCSEL is used to select an alternate synchronization source. The FCSEL choices are a subset
of the CKSEL values from the CKM register above. The list is presented below:
FCSEL = 000,
Internal oscillator divided by 4.
FCSEL = 001,
NETREF2.
FCSEL = 010,
A clocks (C8A & FRAMEA); ECTF or MC-1.
FCSEL = 011,
B clocks (C8B & FRAMEB); ECTF or MC-1.
FCSEL = 100,
NETREF1.
FCSEL = 101—111,
Selects local references 1—3.
Description
FTS
FF
FCSEL
相關PDF資料 |
PDF描述 |
|---|---|
| T8102A | H.100/H.110 Interface and Time-Slot Interchangers |
| T8105A | H.100/H.110 Interface and Time-Slot Interchangers |
| T8100 | H.100/H.110 Interface and Time-Slot Interchanger |
| T8110 | Version History |
| T8301 | T8301 Internet Protocol Telephone Phone-On-A-Chip⑩ IP Solution DSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T8100A-BAL | 制造商:Alcatel-Lucent 功能描述:ELECTRONIC COMPONENT |
| T8100A-BAL4DB | 制造商:AGERE 功能描述: |
| T8100-D | 制造商:GE Sensing & Inspection Technologies 功能描述:CO2/TEMP SENS WALL MNT DUAL OUT |
| T8100-E | 制造商:GE Sensing & Inspection Technologies 功能描述:TRANSMITTER, CO2, HUMIDITY, TEMP 制造商:GE MEASUREMENT & CONTROL 功能描述:TRANSMITTER, CO2, HUMIDITY, TEMP; Plug Type:- ;RoHS Compliant: Yes 制造商:GE MEASUREMENT & CONTROL/GE SENSING 功能描述:TRANSMITTER, CO2, HUMIDITY, TEMP; Plug Type:- ;RoHS Compliant: Yes |
| T8100-E-D | 制造商:GE Sensing & Inspection Technologies 功能描述:TRANSMITTER, CO2, HUMIDITY, TEMP 制造商:GE MEASUREMENT & CONTROL 功能描述:TRANSMITTER, CO2, HUMIDITY, TEMP; Plug Type:- ;RoHS Compliant: Yes 制造商:GE MEASUREMENT & CONTROL/GE SENSING 功能描述:TRANSMITTER, CO2, HUMIDITY, TEMP; Plug Type:- ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。