- 您現在的位置：買賣IC網 > PDF目錄371179 > T8100A H.100/H.110 Interface and Time-Slot Interchangers PDF資料下載
參數資料
| 型號： | T8100A |
| 英文描述： | H.100/H.110 Interface and Time-Slot Interchangers |
| 中文描述： | H.100/H.110接口和時隙Interchangers |
| 文件頁數： | 73/112頁 |
| 文件大小： | 1408K |
| 代理商： | T8100A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁當前第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁
Lucent Technologies Inc.
69
Advance Data Sheet
November 1999
H.100/H.110 Interfaces and Time-Slot Interchangers
Ambassador T8100A, T8102, and T8105
3 Using the TSI Devices
3.1 Resets
3.1.1 Hardware Reset
A hardware reset utilizes the (active-low) RESET pin.
On activation, it immediately places all outputs into
3-state. Individual output sections must be re-enabled
by setting the appropriate bits high in the MCR register.
Internally, the local memory (T8100A, T8105 only) is in
an undefined state, all CAM empty bits are set, all state
machines are reset, and all registers are cleared to
zero.
3.1.2 Software Reset
This is accomplished by setting the MSB of the master
control and status register (see Section 2.1.2 Master
Control and Status Register). The local and H-bus con-
nections are rendered invalid, all registers are cleared
except MCR, CLKERR1, CLKERR2, CLKERR3, and
SYSERR (these registers are cleared with separate
MCR control bits); the state machines are also reset.
Writing the value 0xE0 to the MCR is a full software
reset. Writing 0x0E enables all pin groups (though indi-
vidual pins still require setup). This soft reset is clocked
by the crystal.
3.1.3 Power-On Reset
No power-on reset is available. It is expected that the
host microprocessor or applications board will provide
an external control to the RESET pin for performing a
hardware reset. The PLLs must not be enabled prior to
establishing a stable supply voltage. There are two
methods to accomplish this:
I
Tie the En1 and En2 pins to the same line that drives
the RESET, which forces the PLLs into an off condi-
tion while the devices reset asynchronously.
I
Add external capacitors from En1 to ground and from
En2 to ground. (The values of the capacitors should
be 1 μF or greater.) The capacitors will form RC cir-
cuits with the En1 and En2 internal pull-ups and will
charge up to enable the PLLs after several millisec-
onds. The RC circuit affects the power-on reset for
the PLLs. The long rise time provides some delay.
相關PDF資料 |
PDF描述 |
|---|---|
| T8102A | H.100/H.110 Interface and Time-Slot Interchangers |
| T8105A | H.100/H.110 Interface and Time-Slot Interchangers |
| T8100 | H.100/H.110 Interface and Time-Slot Interchanger |
| T8110 | Version History |
| T8301 | T8301 Internet Protocol Telephone Phone-On-A-Chip⑩ IP Solution DSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T8100A-BAL | 制造商:Alcatel-Lucent 功能描述:ELECTRONIC COMPONENT |
| T8100A-BAL4DB | 制造商:AGERE 功能描述: |
| T8100-D | 制造商:GE Sensing & Inspection Technologies 功能描述:CO2/TEMP SENS WALL MNT DUAL OUT |
| T8100-E | 制造商:GE Sensing & Inspection Technologies 功能描述:TRANSMITTER, CO2, HUMIDITY, TEMP 制造商:GE MEASUREMENT & CONTROL 功能描述:TRANSMITTER, CO2, HUMIDITY, TEMP; Plug Type:- ;RoHS Compliant: Yes 制造商:GE MEASUREMENT & CONTROL/GE SENSING 功能描述:TRANSMITTER, CO2, HUMIDITY, TEMP; Plug Type:- ;RoHS Compliant: Yes |
| T8100-E-D | 制造商:GE Sensing & Inspection Technologies 功能描述:TRANSMITTER, CO2, HUMIDITY, TEMP 制造商:GE MEASUREMENT & CONTROL 功能描述:TRANSMITTER, CO2, HUMIDITY, TEMP; Plug Type:- ;RoHS Compliant: Yes 制造商:GE MEASUREMENT & CONTROL/GE SENSING 功能描述:TRANSMITTER, CO2, HUMIDITY, TEMP; Plug Type:- ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。