參數資料
型號： T8100A
英文描述： H.100/H.110 Interface and Time-Slot Interchangers
中文描述： H.100/H.110接口和時隙Interchangers
文件頁數： 84/112頁
文件大小： 1408K
代理商： T8100A
80
Lucent Technologies Inc.
Advance Data Sheet
November 1999
H.100/H.110 Interfaces and Time-Slot Interchangers
Ambassador T8100A, T8102, and T8105
3 Using the TSI Devices
(continued)
3.4 Using the LAR, AMR, and IDR for Connections
(continued)
3.4.3 Programming Examples
(continued)
;*******EXAMPLE #2 - Setting up Local Connections (T8100A, T8105 only)
;
;
Use 8 Mbits/s rate set up from Example #1...
;
Send data FROM Stream/Time Slot 14, 7 TO Stream/Time Slot 3, 29.
;
To transfer data the local input 14, 7 to the local
;
output 3, 29 the following programming steps are required.
;
MD,LAR,1Dh
;Set up lower address, i.e., Time Slot 29
MD,AMR,43h
;
Set up upper address bits (Stream 3), and
point to the
;
the Time Slot field of the connection memory
MI,IDR,07h
;Put a “7” in the Time Slot field of connection location
3,29
;
;Syntactically, “MI,IDR,data” is a special case since IDR is not the final recipient
of the data
;
MD,AMR,53h
;Maintain the same upper address, but get ready to load the
;
remaining connection info (upper bits +
control)
MI,IDR,0001_1110b
;This decodes as follows: XCS bit low, pattern mode off
;
(not set), frame bit low, time slot enabled,
and stream = 1110b (14)
;
;*******END OF EXAMPLE #2
;*******EXAMPLE #3 - Setting up H-Bus Connections, No Subrate
;
; Use rate set up from Example #1...
; Send data from Stream 14/Time Slot 7 of the H.100 bus to Stream 3/Time Slot 29
; on the Local side. The data is coming in at 4 Mbits/s from E-CAM, and is sent
; out at 8 Mbits/s to through L-CAM. We’re using Data Memory location 49 to hold
; the actual data. LAR is not used for the CAM connection setups; it is used for
; reading specific CAM locations or writing and reading the associated Data
; Memory Locations.
;
;******Set up the “from” connection
;
MD,AMR,0B0h
;Point to the Time-Slot holding register
MI,IDR,07h
;This is the Time-Slot value (7) for the H-Bus address
MD,AMR,0B1h
;Point to the upper bits of the connection
MI,IDR,000_01110b
:Set up a write into data memory from ECTF bus,
;
disable pattern mode, minimum delay,
;
and set stream number equal to 01110b (14).
MD,AMR,0B2h
;Point to tag field
MI,IDR,31h
;Use location 49 of the associated Data RAM to store the data
MD,AMR,0B3h
;Point to the subrate control and TAG MSB field;
MI,IDR,00h
;MSB of location 49 is 0;
;
MD,AMR,0E0h
;Write to next free location in the Even CAM
MI,IDR,0E0h
;The command is executed with the indirect to IDR which
;uses the same command value as in the AMR.
相關PDF資料
PDF描述
T8102A H.100/H.110 Interface and Time-Slot Interchangers
T8105A H.100/H.110 Interface and Time-Slot Interchangers
T8100 H.100/H.110 Interface and Time-Slot Interchanger
T8110 Version History
T8301 T8301 Internet Protocol Telephone Phone-On-A-Chip⑩ IP Solution DSP
相關代理商/技術參數
參數描述
T8100A-BAL 制造商:Alcatel-Lucent 功能描述:ELECTRONIC COMPONENT
T8100A-BAL4DB 制造商:AGERE 功能描述:
T8100-D 制造商:GE Sensing & Inspection Technologies 功能描述:CO2/TEMP SENS WALL MNT DUAL OUT
T8100-E 制造商:GE Sensing & Inspection Technologies 功能描述:TRANSMITTER, CO2, HUMIDITY, TEMP 制造商:GE MEASUREMENT & CONTROL 功能描述:TRANSMITTER, CO2, HUMIDITY, TEMP; Plug Type:- ;RoHS Compliant: Yes 制造商:GE MEASUREMENT & CONTROL/GE SENSING 功能描述:TRANSMITTER, CO2, HUMIDITY, TEMP; Plug Type:- ;RoHS Compliant: Yes
T8100-E-D 制造商:GE Sensing & Inspection Technologies 功能描述:TRANSMITTER, CO2, HUMIDITY, TEMP 制造商:GE MEASUREMENT & CONTROL 功能描述:TRANSMITTER, CO2, HUMIDITY, TEMP; Plug Type:- ;RoHS Compliant: Yes 制造商:GE MEASUREMENT & CONTROL/GE SENSING 功能描述:TRANSMITTER, CO2, HUMIDITY, TEMP; Plug Type:- ;RoHS Compliant: Yes
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*