www.national.com
222
Revision 1.1
G
Core Logic Module
(Continued)
3
GPIO_EN.
Allow GPIOs (GPIO47-GPIO32 and GPIO15-GPIO0) to
generate an SCI.
0: Disable.
1: Enable.
F0BAR0+I/O Offset 08h/18h selects which GPIOs are enabled for PME generation. This bit (GPIO_EN) globally enables
those selected GPIOs for generation of an SCI.
Reserved.
Must be set to 0.
PWR_U_REQ_EN.
Allow power-up request events from the SuperI/O module to generate an SCI.
0: Disable.
1: Enable.
A power-up request event is defined as any of the following events/activities: Modem, Telephone, Keyboard, Mouse, CEIR
(Consumer Electronic Infrared)
2:1
0
Offset 14h
GPWIO Control Register 1 (R/W)
Reset Value: 00h
7:3
2
Reserved.
Must be set to 0.
GPWIO2_POL.
Select GPWIO2 (ball AF17) polarity.
0: Active high.
1: Active low.
GPWIO1_POL.
Select GPWIO1 (ball AE16) polarity.
0: Active high.
1: Active low.
GPWIO0_POL.
Select GPWIO0 (ball AC15) polarity.
0: Active high.
1: Active low.
1
0
Offset 15h
GPWIO Control Register 2 (R/W)
Reset Value: 00h
7
6
Reserved.
Must be set to 0.
GPWIO_SMIEN2.
Allow GPWIO2 (ball AF17) to generate an SMI.
0: Disable. (Default)
1: Enable.
A fixed high-to-low or low-to-high transition (debounce period) of 31 μs exists in order for GPWIO2 to be recognized.
Bit 2 of this register must be set to 0 (input) for GPWIO2 to be able to generate an SMI.
If asserted, this bit overrides the setting of F1BAR1+I/O Offset 12h[10] and its status is reported in F1BAR0+I/O Offset
00h/02h[0].
GPWIO_SMIEN1.
Allow GPWIO1 (ball AE16) to generate an SMI.
0: Disable. (Default)
1: Enable.
See F1BAR1+I/O Offset 07h[3] for debounce information.
Bit 1 of this register must be set to 0 (input) for GPWIO1 to be able to generate an SMI.
If asserted, this bit overrides the setting of F1BAR1+I/O Offset 12h[9] and its status is reported in F1BAR0+I/O Offset
00h/02h[0].
GPWIO_SMIEN0.
Allow GPWIO0 (ball AC15) to generate an SMI.
0: Disable. (Default)
1: Enable.
See F1BAR1+I/O Offset 07h[3] for debounce information.
Bit 0 of this register must be set to 0 (input) for GPWIO0 to be able to generate an SMI.
If enabled, this bit overrides the setting of F1BAR1+I/O Offset 12h[8] and its status is reported in F1BAR0+I/O Offset
00h/02h[0].
Reserved.
Set to 0.
GPWIO2_DIR.
Selects the direction of GPWIO2 (ball AF17).
0: Input.
1: Output.
5
4
3
2
Table 5-34. F1BAR1+I/O Offset: ACPI Support Registers (Continued)
Bit
Description