參數資料
型號: SC1100UFH-233
廠商: National Semiconductor Corporation
英文描述: Geode⑩ Information Appliance On a Chip
中文描述: Geode⑩信息家電在一個芯片
文件頁數: 92/348頁
文件大?。?/td> 2063K
代理商: SC1100UFH-233
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁當前第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁第262頁第263頁第264頁第265頁第266頁第267頁第268頁第269頁第270頁第271頁第272頁第273頁第274頁第275頁第276頁第277頁第278頁第279頁第280頁第281頁第282頁第283頁第284頁第285頁第286頁第287頁第288頁第289頁第290頁第291頁第292頁第293頁第294頁第295頁第296頁第297頁第298頁第299頁第300頁第301頁第302頁第303頁第304頁第305頁第306頁第307頁第308頁第309頁第310頁第311頁第312頁第313頁第314頁第315頁第316頁第317頁第318頁第319頁第320頁第321頁第322頁第323頁第324頁第325頁第326頁第327頁第328頁第329頁第330頁第331頁第332頁第333頁第334頁第335頁第336頁第337頁第338頁第339頁第340頁第341頁第342頁第343頁第344頁第345頁第346頁第347頁第348頁
www.national.com
92
Revision 1.1
G
SuperI/O Module
(Continued)
4.6
The SWC wakes up the system by sending a power-up
request to the ACPI controller in response to the following
maskable system events:
SYSTEM WAKEUP CONTROL (SWC)
Modem ring (RI#)
Programmable Consumer Electronics IR (CEIR)
address
Each system event that is monitored by the SWC is fed into
a dedicated detector that decides when the event is active,
according to predetermined (either fixed or programmable)
criteria. A set of dedicated registers is used to determine
the wakeup criteria, including the CEIR address.
A Wakeup Events Status Register (WKSR) and a Wakeup
Events Control Register (WKCR) hold a Status bit and
Enable bit, respectively, for each possible wakeup event.
Upon detection of an active event, the corresponding Sta-
tus bit is set to 1. If the event is enabled (the corresponding
Enable bit is set to 1), a power-up request is issued to the
ACPI controller. In addition, detection of an active wakeup
event may be also routed to an arbitrary IRQ.
Disabling an event prevents it from issuing power-up
requests, but does not affect the Status bits. A power-up
reset is issued to the ACPI controller when both the Status
and Enable bits are set to 1 for at least one event type.
SWC logic is powered by V
SB
. The SWC control and con-
figuration registers are battery backed, powered by V
PP
.
The setup of the wakeup events, including programmable
sequences, is retained throughout power failures (no V
SB
)
as long as the battery is connected. V
PP
is taken from V
SB
if V
SB
> 2.0; otherwise, V
BAT
is used as the V
PP
source.
Hardware reset does not affect the SWC registers. They
are reset only by a SIO software reset or power-up of V
PP
.
4.6.1
Event Detection
CEIR Address
A CEIR transmission received on IRRX1 in a pre-selected
standard (NEC, RCA or RC-5) is matched against a pro-
grammable CEIR address. Detection of matching can be
used as a wakeup event. The CEIR address detection
operates independently of the IR port, which is powered
down with the rest of the system.
Whenever an IR signal is detected, the receiver immedi-
ately enters the Active state. When this happens, the
receiver keeps sampling the IR input signal and generates
a bit string where a logic 1 indicates an idle condition and a
logic 0 indicates the presence of IR energy. The received
bit string is de-serialized and assembled into 8-bit charac-
ters.
The expected CEIR protocol of the received signal should
be configured through bits [5:4] of the CEIR Wakeup Con-
trol register (IRWCR) (see Table 4-28 on page 95).
The CEIR Wakeup Address register (IRWAD) holds the
unique address to be compared with the address contained
in the incoming CEIR message. If CEIR is enabled
(IRWCR[0] = 1) and an address match occurs, then the
CEIR Event Status bit of WKSR is set to 1.
The CEIR Address Shift register (ADSR) holds the
received address which is compared with the address con-
tained in the IRWAD. The comparison is affected also by
the CEIR Wakeup Address Mask register (IRWAM) in
which each bit determines whether to ignore the corre-
sponding bit in the IRWAD.
If CEIR routing to interrupt request is enabled, the
assigned SWC interrupt request can be used to indicate
that a complete address has been received. To get this
interrupt when the address is completely received, IRWAM
should be written with FFh. Once the interrupt is received,
the value of the address can be read from ADSR.
Another parameter that is used to determine whether a
CEIR signal is to be considered valid is the bit cell time
width. There are four time ranges for the different protocols
and carrier frequencies. Four pairs of registers (IRWTRxL
and IRWTRxH) define the low and high limits of each time
range. Table 4-24 lists the recommended time range limits
for the different protocols and their applicable ranges. The
values are represented in hexadecimal code where the
units are of 0.1 msec.
Table 4-24. Time Range Limits for CEIR Protocols
Time
Range
RC-5
NEC
RCA
Low Limit
High Limit
Low Limit
High Limit
Low Limit
High Limit
0
10h
14h
09h
0Dh
0Ch
12h
1
07h
0Bh
14h
19h
16h
1Ch
2
-
-
50h
64h
B4h
DCh
3
-
-
28h
32h
23h
2Dh
相關PDF資料
PDF描述
SC1100UFH-266 Geode⑩ Information Appliance On a Chip
SC1100UFH-300 Geode⑩ Information Appliance On a Chip
SC11372 MOBILE RADIO ANALOG PROCESSOR
SC11372CQ MOBILE RADIO ANALOG PROCESSOR
SC140 High-Performance Fix-Point DSP Core(高性能定點型數字信號處理器內核)
相關代理商/技術參數
參數描述
SC1100UFH-266 制造商:ADV-MICRO-DEV 功能描述:
SC1100UFH-266 B1 制造商:Advanced Micro Devices 功能描述:I3O IC OPN
SC1100UFH-300 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Geode⑩ Information Appliance On a Chip
SC1101 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:VOLTAGE MODE PWM CONTROLLER
SC1101_05 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Asynchronous Voltage Mode PWM Controller