- 您現在的位置：買賣IC網 > PDF目錄272395 > TE28F800C3TD70 (INTEL CORP) 512K X 16 FLASH 3V PROM, 70 ns, PDSO48 PDF資料下載
參數資料
| 型號： | TE28F800C3TD70 |
| 廠商： | INTEL CORP |
| 元件分類： | PROM |
| 英文描述： | 512K X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| 封裝： | 12 X 20 MM, TSOP-48 |
| 文件頁數： | 36/72頁 |
| 文件大?。?/td> | 1083K |
| 代理商： | TE28F800C3TD70 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
Intel Advanced+ Boot Block Flash Memory (C3)
Datasheet
Intel Advanced+ Boot Block Flash Memory (C3)
May 2005
Order Number: 290645, Revision: 023
41
10.0
Modes of Operation
10.1
Read Mode
The flash memory has four read modes (read array, read identifier, read status, and CFI query) and
two write modes (program and erase). Three additional modes (erase suspend to program, erase
suspend to read, and program suspend to read) are available only during suspended operations.
Descriptions” on page 47 summarize the commands used for these modes.
Appendix A, “Write State Machine States” on page 54 is a comprehensive chart showing the state
transitions.
10.1.1
Read Array
When RP# transitions from VIL (reset) to VIH, the device defaults to read-array mode and will
respond to the read-control inputs (CE#, address inputs, and OE#) without any additional CUI
commands.
When the device is in read array mode, four control signals control data output.
WE# must be logic high (V
IH)
CE# must be logic low (V
IL)
OE# must be logic low (VIL)
RP# must be logic high (VIH)
In addition, the address of the desired location must be applied to the address pins. If the device is
not in read-array mode, as would be the case after a Program or Erase operation, the Read Array
command (0xFF) must be issued to the CUI before array reads can occur.
10.1.2
Read Identifier
The read-identifier mode outputs three types of information: the manufacturer/device identifier, the
block locking status, and the protection register. The device is switched to this mode by issuing the
Read Identifier command (0x90). Once in this mode, read cycles from addresses shown in Table 21
retrieve the specified information. To return to read-array mode, issue the Read Array command
(0xFF).
相關PDF資料 |
PDF描述 |
|---|---|
| T101P3TAKE | TOGGLE SWITCH, SPDT, LATCHED, 0.02A, 20VDC, THROUGH HOLE-RIGHT ANGLE |
| T103STKWBE | TOGGLE SWITCH, SPDT, LATCHED, 0.02A, 20VDC, PANEL MOUNT-THREADED |
| T105KHWGE | TOGGLE SWITCH, SPDT, MOMENTARY, 2A, 28VDC, PANEL MOUNT-THREADED |
| T105KTDCGE | TOGGLE SWITCH, SPDT, MOMENTARY, 2A, 28VDC, THROUGH HOLE-STRAIGHT |
| T107MTDAGE | TOGGLE SWITCH, SPDT, LATCHED AND MOMENTARY, 2A, 28VDC, THROUGH HOLE-RIGHT ANGLE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TE28F800CEB120 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:8-MBIT (512K X 16, 1024K X 8) SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| TE28F800CET120 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:8-MBIT (512K X 16, 1024K X 8) SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| TE28F800CV-B60 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| TE28F800CV-B80 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| TE28F800CVB90 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:8-MBIT (512K X 16, 1024K X 8) SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
發布緊急采購，3分鐘左右您將得到回復。