參數資料
型號： 21440
廠商： Intel Corp.
英文描述： Multiport 10/100Mb/s Ethernet Controller(多端口10/100Mb/s 以太網控制器)
中文描述： 多端口10/100Mb/s以太網控制器（多端口支持10/100Mbps以太網控制器）
文件頁數： 64/92頁
文件大?。?/td> 1352K
代理商： 21440
21440 Multiport 10/100Mb/s Ethernet Controller
6-7
Network Interface Operation
6.5.2
Preamble Processing
The IEEE 802.3 Standard allows a maximum size of 56 bits (7 bytes) for the preamble, while the
21440 allows any arbitrary preamble length. The 21440 checks for the start frame delimiter (SFD)
byte. If the 21440 receives a binary 11 before receiving 6 bits or a binary 00 anywhere while checking
for SFD, the reception of the current frame is aborted. The frame is not received, and the 21440 waits
until the network activity stops before monitoring the network activity for a new preamble.
The interpacket gap (IPG) between received frames should be at least 32-bit times.
6.5.3
Frame Decapsulation
While the frame is being assembled, the 21440 continues to monitor the line condition.
In the MII mode, the 21440 detects the end of frame when the data valid signal (dv{i}) deasserts.
Reception terminates with a frame error if the frame is not a valid MAC frame, or if an MII error
was detected during frame reception.
In the MII mode, an MII error is detected when the receive error signal (rerr{i}) asserts during
frame reception.
The 21440 refers to the last 4 full bytes received as the CRC. It checks the CRC bytes of all
received frames and reports all errors. Only whole bytes are run through the CRC check.
6.5.4
Terminating Reception
When reception terminates, the 21440 determines the status of the received frame and loads the status
into the receive FIFO. The 21440 can report the following events at the end of frame reception:
Overflow
The 21440 receive FIFO is not emptied as rapidly as it is filled, and an error occurs as frame data
is lost. If the FIFO is already full when a new frame is received, it will not be loaded in the FIFO.
CRC error
The 32-bit CRC, transmitted with the frame, did not match the CRC calculated upon reception.
Alignment error
The frame did not end on a byte boundary, but with a spare nibble (4 bits), and a CRC error has
also occurred. If the frame was not composed of an integral number of bytes, but the CRC was
okay, the frame is considered good and no error is reported.
MII error
An MII error was detected during frame reception.
Frame too short
A frame containing less than 64 bytes was received (including CRC).
Frame too long
A frame containing more than the programmed maximum size was received.
相關PDF資料
PDF描述
21446 Net186-EVAL-KT? 24.9KB (PDF)
2145 MONITORKABEL SUN BUCHSE SVGA STECKER
2148C MONITORKABEL SUN STECKER SVGA BUCHSE
2148D MONITORKABEL SUN STECKER SVGA STECKER
2148 MONITORKABEL SUN VGA ADAPTER
相關代理商/技術參數
參數描述
2-1440000-2 制造商:TE Connectivity 功能描述:relay, OMR-C-105H,V000
2-1440000-3 功能描述:低信號繼電器 - PCB OMR-C-105H V300 RoHS:否 制造商:NEC 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 V 最大開關電流:1 A 線圈電流:1 A 線圈類型:Non-Latching 功耗:140 mW 端接類型:SMT 絕緣: 介入損耗:
2-1440000-5 功能描述:低信號繼電器 - PCB OMR-C-109H V530 RoHS:否 制造商:NEC 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 V 最大開關電流:1 A 線圈電流:1 A 線圈類型:Non-Latching 功耗:140 mW 端接類型:SMT 絕緣: 介入損耗:
2-1440000-6 制造商:TE Connectivity 功能描述:Electromechanical Relay SPST-NO 0.5A 12VDC 1.05KOhm Through Hole 制造商:TE Connectivity 功能描述:EM RLY SPST-NO 0.5A 12VDC 1.05KOHM TH - Bulk 制造商:TE Connectivity 功能描述:RELAY REED SPST 500MA 12V
2-1440001-1 功能描述:通用繼電器 OMI-SH-206L 594 RoHS:否 制造商:Omron Electronics 觸點形式:1 Form A (SPST-NO) 觸點電流額定值:150 A 線圈電壓:24 VDC 線圈電阻:144 Ohms 線圈電流:167 mA 切換電壓:400 V 安裝風格:Chassis 觸點材料:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*