- 您現在的位置：買賣IC網 > PDF目錄377798 > LXT386 (Intel Corp.) QUAD T1/E1/J1 Transceiver PDF資料下載
參數資料
| 型號： | LXT386 |
| 廠商： | Intel Corp. |
| 英文描述： | QUAD T1/E1/J1 Transceiver |
| 中文描述： | 四T1/E1/J1收發器 |
| 文件頁數： | 11/78頁 |
| 文件大小： | 500K |
| 代理商： | LXT386 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
QUAD T1/E1/J1 Transceiver
—
LXT386
Datasheet
11
Table 1. Pin Assignments and Signal Descriptions
Ball #
PBGA
Pin #
LQFP
Symbol
I/O
1
Description
E1
78
MCLK
DI
Master Clock
. MCLK is an independent, free-running reference clock. It
’
s
frequency should be 1.544 MHz for T1 operation and 2.048 MHz for E1
operation.
This reference clock is used to generate several internal reference
signals:
Timing reference for the integrated clock recovery unit
Timing reference for the integrated digital jitter attenuator
Generation of RCLK signal during a loss of signal condition
Reference clock during a blue alarm transmit all ones condition
Reference timing for the parallel processor wait state generation logic
If MCLK is High, the PLL clock recovery circuit is disabled. In this mode,
the LXT386 operates as simple data receiver.
If MCLK is Low, the complete receive path is powered down and the
output pins RCLK, RPOS and RNEG are switched to Tri-state mode.
MCLK is not required if LXT386 is used as a simple analog front-end
without clock recovery and jitter attenuation.
Note that wait state generation via RDY/ACK is not available if MCLK is
not provided.
E2
79
MODE
DI
Mode Select
. This pin is used to select the operating mode of the
LXT386. In Hardware Mode, the parallel processor interface is disabled
and hardwired pins are used to control configuration and report status.
In Parallel Host Mode, the parallel port interface pins are used to control
configuration and report status.
In Serial Host Mode the serial interface pins: SDI, SDO, SCLK and
CS are
used.
For Serial Host Mode, the pin should connected to a resistive divider
consisting of two 10 k
resistors across V
CC
and Ground.
F4
89
A4
DI
Address Select
. In host mode, this pin is Address 4 input pin. In hardware
mode this pin must be connected to Ground.
1. DI: Digital Input; DO: Digital Output; DI/O: Digital Bidirectional Port; AI: Analog Input; AO: Analog Output S: Power Supply;
N.C.: Not Connected.
2. N/C means
“
Not Connected
”
MODE
Operating Mode
L
Hardware Mode
H
Parallel Host Mode
Vcc/2
Serial Host Mode
相關PDF資料 |
PDF描述 |
|---|---|
| LXT400 | All Rate Extended Range Switched 56/DDS Transceiver |
| LXT441 | Switched 56/DDS Integrated DSU/CSU |
| LXT6155 | 155 Mbps SDH/SONET/ATM Transceiver |
| LXT6234 | E-Rate Multiplexer |
| LXT901 | 8QLYHUVDO (WKHUQHW 7UDQVFHLYHU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LXT386BE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM TRANSCEIVER|QUAD|CEPT PCM-30/E-1|CMOS|BGA|160PIN|PLASTIC |
| LXT386LE | 制造商:LEVEL1 功能描述: |
| LXT388LE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM TRANSCEIVER|DUAL|CEPT PCM-30/E-1|CMOS|QFP|100PIN|PLASTIC |
| LXT400 | 制造商:LVL1 制造商全稱:LVL1 功能描述:All Rate Extended Range Switched 56/DDS Transceiver |
| LXT400JE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Transceiver Circuit For Telecommunications |
發布緊急采購，3分鐘左右您將得到回復。