- 您現在的位置：買賣IC網 > PDF目錄377798 > LXT386 (Intel Corp.) QUAD T1/E1/J1 Transceiver PDF資料下載
參數資料
| 型號： | LXT386 |
| 廠商： | Intel Corp. |
| 英文描述： | QUAD T1/E1/J1 Transceiver |
| 中文描述： | 四T1/E1/J1收發器 |
| 文件頁數： | 24/78頁 |
| 文件大?。?/td> | 500K |
| 代理商： | LXT386 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
LXT386
—
QUAD T1/E1/J1 Transceiver
24
Datasheet
3.2.1
Loss of Signal Detector
The loss of signal detector in the LXT386 uses a dedicated analog and digital loss of signal
detection circuit. It is independent of its internal data slicer comparators and complies to the latest
ITU G.775 and ANSI T1.231 recommendations. Under software control, the detector can be
configured to comply to the ETSI ETS 300 233 specification (
LACS
Register). In hardware mode,
the LXT386 supports LOS per G.775 for E1 and ANSI T1.231 for T1 operation.
The receiver monitor loads a digital counter at the RCLK frequency. The counter is incremented
each time a zero is received, and reset to zero each time a one (mark) is received. Depending on the
operation mode, a certain number of consecutive zeros sets the LOS signal. The recovered clock is
replaced by MCLK at the RCLK output with a minimum amount of phase errors. MCLK is
required for receive operation. When the LOS condition is cleared, the LOS flag is reset and
another transition replaces MCLK with the recovered clock at RCLK. RPOS/RNEG will reflect the
data content at the receiver input during the entire LOS detection period for that channel.
3.2.1.1
E1 Mode
In G.775 mode a loss of signal is detected if the signal is below 200mV (typical) for 32 consecutive
pulse intervals. When the received signal reaches 12.5% ones density (4 marks in a sliding 32-bit
period) with no more than 15 consecutive zeros and the signal level exceeds 250mV (typical), the
LOS flag is reset and another transition replaces MCLK with the recovered clock at RCLK.
In ETSI 300 233 mode, a loss of signal is detected if the signal is below 200mV for 2048
consecutive intervals (1 ms). The LOS condition is cleared and the output pin returns to Low when
the incoming signal has transitions when the signal level is equal or greater than 250mV for more
than 32 consecutive pulse intervals. This mode is activated by setting the LACS register bit to one.
If it is necessary to use AIS with LOS, see errata 10.3 for a way to implement this.
3.2.1.2
T1 Mode
The T1.231 LOS detection criteria is employed. LOS is detected if the signal is below 200mV for
175 contiguous pulse positions. The LOS condition is terminated upon detecting an average pulse
density of 12.5% over a period of 175 contiguous pulse positions starting with the receipt of a
pulse. The incoming signal is considered to have transitions when the signal level is equal or
greater than 250mV.
3.2.1.3
Data Recovery Mode
In data recovery mode the LOS digital timing is derived from a internal self timed circuit. RPOS/
RNEG stay active during loss of signal. The analog LOS detector complies with ITU-G.775
recommendation. The LXT386 monitors the incoming signal amplitude. Any signal below 200mV
for more than 30
μ
s (typical) will assert the corresponding LOS pin. The LOS condition is cleared
when the signal amplitude rises above 250mV. The LXT386 requires more than 10 and less than
255 bit periods to declare a LOS condition in accordance to ITU G.775.
3.2.2
Alarm Indication Signal (AIS) Detection
The AIS detection is performed by the receiver independent of any loopback mode. This feature is
available in host mode only. Because there is no clock in data recovery mode, AIS detection will
not work in that mode. AIS requires MCLK to have clock applied, since this function depends on
the clock to count the number of ones in an interval.
相關PDF資料 |
PDF描述 |
|---|---|
| LXT400 | All Rate Extended Range Switched 56/DDS Transceiver |
| LXT441 | Switched 56/DDS Integrated DSU/CSU |
| LXT6155 | 155 Mbps SDH/SONET/ATM Transceiver |
| LXT6234 | E-Rate Multiplexer |
| LXT901 | 8QLYHUVDO (WKHUQHW 7UDQVFHLYHU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LXT386BE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM TRANSCEIVER|QUAD|CEPT PCM-30/E-1|CMOS|BGA|160PIN|PLASTIC |
| LXT386LE | 制造商:LEVEL1 功能描述: |
| LXT388LE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM TRANSCEIVER|DUAL|CEPT PCM-30/E-1|CMOS|QFP|100PIN|PLASTIC |
| LXT400 | 制造商:LVL1 制造商全稱:LVL1 功能描述:All Rate Extended Range Switched 56/DDS Transceiver |
| LXT400JE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Transceiver Circuit For Telecommunications |
發布緊急采購，3分鐘左右您將得到回復。