- 您現在的位置：買賣IC網 > PDF目錄377798 > LXT386 (Intel Corp.) QUAD T1/E1/J1 Transceiver PDF資料下載
參數資料
| 型號： | LXT386 |
| 廠商： | Intel Corp. |
| 英文描述： | QUAD T1/E1/J1 Transceiver |
| 中文描述： | 四T1/E1/J1收發器 |
| 文件頁數： | 23/78頁 |
| 文件大?。?/td> | 500K |
| 代理商： | LXT386 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
QUAD T1/E1/J1 Transceiver
—
LXT386
Datasheet
23
3.2
Receiver
The four receivers in the LXT386 are identical. The following paragraphs describe the operation of
one.
The twisted-pair input is received via a 1:2 step down transformer. Positive pulses are received at
RTIP, negative pulses at RRING. Recovered data is output at RPOS and RNEG in the bipolar mode
and at RDATA in the unipolar mode. The recovered clock is output at RCLK. RPOS/RNEG
validation relative to RCLK is pin selectable (CLKE).
The receive signal is processed through the peak detector and data slicers. The peak detector
samples the received signal and determines its maximum value. A percentage of the peak value is
provided to the data slicers as a threshold level to ensure optimum signal-to-noise ratio. For DSX-1
applications (line length inputs LEN2-0 from 011 to 111) the threshold is set to 70% (typical) of the
peak value. This threshold is maintained above the specified level for up to 15 successive zeros
over the range of specified operating conditions. For E1 applications (LEN2-0 = 000), the
threshold is 50% (typical).
The receiver is capable of accurately recovering signals with up to 12 dB of attenuation (from 2.4
V), corresponding to a received signal level of approximately 500 mV. Maximum line length is
1500 feet of ABAM cable (approximately 6 dB of attenuation). Regardless of received signal level,
the peak detectors are held above a minimum level of 0.150 V (typical) to provide immunity from
impulsive noise.
After processing through the data slicers, the received signal goes to the data and timing recovery
section. The data and timing recovery circuits provide an input jitter tolerance better than required
by Pub 62411 and ITU G.823, as shown in Test Specifications,
Figure 33
.
Depending on the options selected, recovered clock and data signals may be routed through the
jitter attenuator, through the B8ZS/HDB3/AMI decoder, and may be output to the framer as either
bipolar or unipolar data.
Figure 5. Pullup Resistor to RESET
LXT386LE
VCC
1K
100
RESET
相關PDF資料 |
PDF描述 |
|---|---|
| LXT400 | All Rate Extended Range Switched 56/DDS Transceiver |
| LXT441 | Switched 56/DDS Integrated DSU/CSU |
| LXT6155 | 155 Mbps SDH/SONET/ATM Transceiver |
| LXT6234 | E-Rate Multiplexer |
| LXT901 | 8QLYHUVDO (WKHUQHW 7UDQVFHLYHU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LXT386BE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM TRANSCEIVER|QUAD|CEPT PCM-30/E-1|CMOS|BGA|160PIN|PLASTIC |
| LXT386LE | 制造商:LEVEL1 功能描述: |
| LXT388LE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM TRANSCEIVER|DUAL|CEPT PCM-30/E-1|CMOS|QFP|100PIN|PLASTIC |
| LXT400 | 制造商:LVL1 制造商全稱:LVL1 功能描述:All Rate Extended Range Switched 56/DDS Transceiver |
| LXT400JE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Transceiver Circuit For Telecommunications |
發布緊急采購，3分鐘左右您將得到回復。