參數資料
型號: T7630
廠商: Lineage Power
英文描述: Dual T1/E1 5.0 V Short-Haul Terminator (Terminator-II)(雙 T1/E1 5.0V短距離通信終端器)
中文描述: 雙T1/E1的5.0V的短途終結者(終結者-Ⅱ)(雙個T1/E1 5.0V短距離通信終端器)
文件頁數: 41/210頁
文件大?。?/td> 3075K
代理商: T7630
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁
Lucent Technologies Inc.
Lucent Technologies Inc.
41
Preliminary Data Sheet
October 2000
T7630 Dual T1/E1 5.0 V Short-Haul Terminator (Terminator-II)
Line Interface Unit: Loopbacks
The LIU has independent loopback paths that are acti-
vated using LOOPA and LOOPB control bits (register
LIU_REG5, bits 2 to 3) as shown in Table 10. The loca-
tions of these loopbacks are illustrated in Figure 5,
Block Diagram of Line Interface Unit: Single Channel.
Full Local Loopback (FLLOOP)
A full local loopback (FLLOOP) connects the LIU trans-
mit driver input to the receive analog front-end circuitry.
Valid transmit output data continues to be sent to the
network. If the LIU transmitter AIS signal (all-ones sig-
nal) is sent to the network, by setting the XLAIS bit
(register LIU_REG5, bit 1), the looped data is not
affected. The ALOS alarm continues to monitor the
receive line interface signal (RTIP and RRING) while
the DLOS alarm monitors the looped data.
See Digital Loss of Signal (DLOS) Alarm section on
page 26 regarding the behavior of the DLOS alarm
upon activation of FLLOOP
Remote Loopback (RLOOP)
A remote loopback (RLOOP) connects the recovered
clock and retimed data to the LIU transmitter at the
framer interface and sends the data back to the line.
The LIU receiver front end, clock/data recovery,
encoder/decoder (if enabled), jitter attenuator (if
enabled), and LIU transmitter driver circuitry are all
exercised during this loopback. The transmit clock,
transmit data, and the transmit AIS inputs are ignored.
Valid receive output data continues to be sent to RPD-
LIU and RND-LIU. This loopback mode is very helpful
in isolating failures between systems.
See Loss of LIU Transmit Clock (LOTC) Alarm section
and LIU Transmitter Driver Monitor on page 33 regard-
ing the behavior of the LOTC and TDM alarms upon
activation and deactivation of RLOOP
Digital Local Loopback (DLLOOP)
A digital local loopback (DLLOOP) connects the trans-
mit clock and data through the encoder/decoder pair to
the receive clock and data output pins. This loopback is
operational regardless of whether the encoder/decoder
pair is enabled or disabled. The alarm indication signal
can be transmitted (XLAIS = 1) without any effect on
the looped signal.
Table 11. Loopback Control
1. The reset default condition is LOOPA = LOOPB = 0 (no loopback).
2. During the transmit AIS condition, the looped data will be the
transmitted data from the framer or system interface and not the all
ones signal.
3. Transmit AIS request is ignored.
Line Interface Unit: Other Features
LIU Powerdown (PWRDN)
Each LIU channel has an independent powerdown
mode controlled by PWRDN (register LIU_REG5,
bit 0). This provides power savings for systems which
use backup channels. If PWRDN = 1, the correspond-
ing LIU channel will be in a standby mode consuming
only a small amount of power. It is recommended that
the alarm registers for the powered down LIU channel
be disabled by setting ALOSIE = DLOSIE = TDMIE =
LOTCIE = 0 (register LIU_REG1, bits 0—3). If an LIU
channel in powerdown mode needs to be placed back
into service, the channel should be turned on (PWRDN
= 0) approximately 5 ms before data is applied.
Loss of Framer Receive Line Clock (LOFRM-
RLCK Pin)
The LOFRMRLCK (pin 2/38) is set when the internal
framer receive line clock is absent. During this alarm
condition, the clock recovery and jitter attenuator func-
tions are automatically disabled. If JAR = 1, the RLCK-
LIU, RPD-LIU, RND-LIU, and DLOS signals will be
unknown.
In-Circuit Testing and Driver High-Imped-
ance State (3-STATE)
If 3-STATE (pin 42/140) is activated (3-STATE = 0), the
outputs TTIP TRING, RDY_DTACK, INTERRUPT, and
AD[7:0] are placed in a high-impedance state. The
TTIP and TRING outputs have a limiting high-imped-
ance capability of approximately 8 k
.
Operation
Symbol
LOOPA LOOPB
Normal
1
Full Local Loopback
Remote Loopback
Digital Local Loopback
0
0
1
1
0
1
0
1
FLLOOP
2
RLOOP
3
DLLOOP
相關PDF資料
PDF描述
T8100A H.100/H.110 Interface and Time-Slot Interchangers
T8102A H.100/H.110 Interface and Time-Slot Interchangers
T8105A H.100/H.110 Interface and Time-Slot Interchangers
T8100 H.100/H.110 Interface and Time-Slot Interchanger
T8110 Version History
相關代理商/技術參數
參數描述
T7630426 制造商:COOPER INDUSTRIES 功能描述:CC ACCESYS / #2450 3/8 Spring Snap Link Stainless Steel UPC Tagged
T-7630-TL2-DB 制造商:Legerity 功能描述:5V DUAL T1/E1 SHORT-HAUL TERMINATOR
T7633 制造商:AGERE 制造商全稱:AGERE 功能描述:Dual T1/E1 3.3 V Short-Haul Terminator
T7645036 功能描述:手工工具 Campbell Snap Link #2450, 7/16", Steel RoHS:否 制造商:Molex 產品:Extraction Tools 類型: 描述/功能:Extraction tool
T7645106 制造商:COOPER INDUSTRIES 功能描述:CC ACCESYS / #7350 1/8 Quick Link Steel Zinc Plated UPC Tagged