- 您現在的位置：買賣IC網 > PDF目錄371179 > T7630 T7630 Dual T1/E1 5.0 V Short-Haul Terminator (Terminator-II) PDF資料下載
參數資料
| 型號： | T7630 |
| 英文描述： | T7630 Dual T1/E1 5.0 V Short-Haul Terminator (Terminator-II) |
| 中文描述： | T7630雙T1/E1的5.0V的短途終結者（終結者-Ⅱ） |
| 文件頁數： | 105/210頁 |
| 文件大小： | 3075K |
| 代理商： | T7630 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁當前第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁
Lucent Technologies Inc.
Lucent Technologies Inc.
105
Preliminary Data Sheet
October 2000
T7630 Dual T1/E1 5.0 V Short-Haul Terminator (Terminator-II)
Facility Data Link (FDL)
(continued)
Flags
*
All flags have the bit pattern 01111110 and are used for
frame synchronization. The FDL HDLC block automati-
cally sends two flags between frames. If the chip-con-
figuration register FDL_PR0 bit 1 (FLAGS) is cleared to
0, the ones idle byte (11111111) is sent between
frames if no data is present in the FIFO. If FLAGS is set
to 1, the FDL HDLC block sends continuous flags when
the transmit FIFO is empty. The FDL HDLC does not
transmit consecutive frames with a shared flag; there-
fore, two successive flags will not share the intermedi-
ate 0.
An opening flag is generated at the beginning of a
frame (indicated by the presence of data in the transmit
FIFO and the transmitter enable register FDL_PR1 bit
3 = 1). Data is transmitted per the HDLC protocol until
a byte is read from the FIFO while register FDL_PR3
bit 7 (FTFC) set to 1. The FDL HDLC block follows this
last user data byte with the CRC sequence and a clos-
ing flag.
The receiver recognizes the 01111110 pattern as a
flag. Two successive flags may or may not share the
intermediate 0 bit and are identified as two flags (i.e.,
both 011111101111110 and 0111111001111110 are
recognized as flags by the FDL HDLC block). When the
second flag is identified, it is treated as the closing flag.
As mentioned above, a flag sequence in the user data
or CRC bits is prevented by zero-bit insertion and dele-
tion. The HDLC receiver recognizes a single flag
between frames as both a closing and opening flag.
Aborts
An abort is indicated by the bit pattern of the sequence
01111111. A frame can be aborted by writing a 1 to
register FDL_PR3 bit 6 (FTABT). This causes the last
byte written to the transmit FIFO to be replaced with
the abort sequence upon transmission. Once a byte is
tagged by a write to FTABT, it cannot be cleared by
subsequent writes to register FDL_PR3. FTABT has
higher priority than FDL transmit frame complete
(FTFC), but FTABT and FTFC should never be set to 1
simultaneously since this causes the transmitter to
enter an invalid state requiring a transmitter reset to
clear. A frame should not be aborted in the very first
byte following the opening flag. An easy way to avoid
this situation is to first write a dummy byte into the
queue and then write the abort command to the queue.
When receiving a frame, the receiver recognizes the
abort sequence whenever it receives a 0 followed by
seven consecutive ones. The receive FDL unit will
abort a frame whenever the receive framer detects a
loss of frame alignment. This results in the abort bit,
and possibly the bad byte count bit and/or bad CRC
bits, being set in the status of frame status byte (see
Table 54) which is appended to the receive data queue.
All subsequent bytes are ignored until a valid opening
flag is received.
Idles
In accordance with the HDLC protocol, the HDLC block
recognizes 15 or more contiguous received ones as
idle. When the HDLC block receives 15 contiguous
ones, the receiver idle bit register FDL_SR0 bit 6
(RIDL) is set.
For transmission, the ones idle byte is defined as the
binary pattern 11111111 (FF (hex)). If the FLAGS con-
trol bit in register FDL_PR0 bit 1 is 0, the ones idle byte
is sent as the time-fill byte between frames. A time-fill
byte is sent when the transmit FIFO is empty and the
transmitter has completed transmission of all previous
frames. Frames are sent back-to-back otherwise.
CRC-16
For given user data bits, 16 additional bits that consti-
tute an error-detecting code (CRC-16) are added by
the transmitter. As called for in the HDLC protocol, the
frame check sequence bits are transmitted most signifi-
cant bit first and are bit stuffed. The cyclic redundancy
check (or frame check sequence) is calculated as a
function of the transmitted bits by using the ITU-T stan-
dard polynomial:
x
16
+ x
12
+ x
5
+ 1
The transmitter can be instructed to transmit a cor-
rupted CRC by setting register FDL_PR2 bit 7 (FTB-
CRC) to 1. As long as the FTBCRC bit is set, the CRC
is corrupted for each frame transmitted by logically flip-
ping the least significant bit of the transmitted CRC.
The receiver performs the same calculation on the
received bits after destuffing and compares the results
to the received CRC-16 bits. An error indication occurs
if, and only if, there is a mismatch.
* Regardless of the time-fill byte used, there always is an opening
and closing flag with each frame. Back-to-back frames are sepa-
rated by two flags.
相關PDF資料 |
PDF描述 |
|---|---|
| T7630 | Dual T1/E1 5.0 V Short-Haul Terminator (Terminator-II)(雙 T1/E1 5.0V短距離通信終端器) |
| T8100A | H.100/H.110 Interface and Time-Slot Interchangers |
| T8102A | H.100/H.110 Interface and Time-Slot Interchangers |
| T8105A | H.100/H.110 Interface and Time-Slot Interchangers |
| T8100 | H.100/H.110 Interface and Time-Slot Interchanger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T7630426 | 制造商:COOPER INDUSTRIES 功能描述:CC ACCESYS / #2450 3/8 Spring Snap Link Stainless Steel UPC Tagged |
| T-7630-TL2-DB | 制造商:Legerity 功能描述:5V DUAL T1/E1 SHORT-HAUL TERMINATOR |
| T7633 | 制造商:AGERE 制造商全稱:AGERE 功能描述:Dual T1/E1 3.3 V Short-Haul Terminator |
| T7645036 | 功能描述:手工工具 Campbell Snap Link #2450, 7/16", Steel RoHS:否 制造商:Molex 產品:Extraction Tools 類型: 描述/功能:Extraction tool |
| T7645106 | 制造商:COOPER INDUSTRIES 功能描述:CC ACCESYS / #7350 1/8 Quick Link Steel Zinc Plated UPC Tagged |
發布緊急采購，3分鐘左右您將得到回復。