- 您現在的位置：買賣IC網 > PDF目錄371179 > T7630 T7630 Dual T1/E1 5.0 V Short-Haul Terminator (Terminator-II) PDF資料下載
參數資料
| 型號： | T7630 |
| 英文描述： | T7630 Dual T1/E1 5.0 V Short-Haul Terminator (Terminator-II) |
| 中文描述： | T7630雙T1/E1的5.0V的短途終結者（終結者-Ⅱ） |
| 文件頁數： | 196/210頁 |
| 文件大小： | 3075K |
| 代理商： | T7630 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁當前第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁
Preliminary Data Sheet
October 2000
T7630 Dual T1/E1 5.0 V Short-Haul Terminator (Terminator II)
196
L Lucent Technologies Inc.
FDL Parameter/Control Registers (800—80E; E00—E0E)
(continued)
Table 194. FDL Interrupt Status Register (Clear on Read) (FDL_SR0) (80B; E0B)
* If an FDL receive FIFO overrun occurs, as indicated by register FDL_SR0 bit 5 (FROVERUN) = 1, the FDL must be reset to restore proper
operation of the FIFO. Following an FDL receive FIFO overrun, data extracted prior to the required reset may be corrupted.
Bit
0
Symbol
FTDONE
Description
Transmit Done.
This status bit is set to 1 when transmission of the current FDL frame
has been completed, either after the last bit of the closing flag or after the last bit of an
abort sequence. In the transparent mode (FDL_PR9 bit 6 = 1), this status bit is set when
the transmit FIFO is completely empty. A hardware interrupt is generated only if the cor-
responding interrupt-enable bit (FDL_PR2 bit 0) is set. This status bit is cleared to 0 by a
read of this register.
Transmitter Empty.
If this bit is set to 1, the FDL transmit FIFO is at or below the pro-
grammed depth. A hardware interrupt is generated only if the corresponding interrupt-
enable bit (FDL_PR2 bit 1) is set. If DINT (FDL_PR0 bit 0) is 0, this status bit is cleared
by a read of this register. If FDINT (FDL_PR0 bit 0) is set to 1, this bit actually represents
the dynamic transmit empty condition, and is cleared to 0 only when the transmit FIFO is
loaded above the programmed empty level.
FDL Transmit Underrun Abort.
A 1 indicates that an abort was transmitted because of
a transmit FIFO underrun. A hardware interrupt is generated only if the corresponding
interrupt-enable bit (FDL_PR2 bit 2) is set. This status bit is cleared to 0 by a read of this
register. This bit must be cleared to 0 before further transmission of data is allowed. This
interrupt is not generated in the transparent mode.
FDL Receiver Full.
This bit is set to 1 when the receive FIFO is at or above the pro-
grammed full level (FDL_PR6). A hardware interrupt is generated if the corresponding
interrupt-enable bit (FDL_PR2 bit 3) is set. If FDINT (FDL_PR0 bit 0) is 0, this status bit
is cleared to 0 by a read of this register. If FDINT (FDL_PR0 bit 0) is set to 1, then this bit
is cleared only when the receive FIFO is read (or emptied) below the programmed full
level*.
FDL Receive End of Frame.
This bit is set to 1 when the receiver has finished receiving
a frame. It becomes 1 upon reception of the last bit of the closing flag of a frame or the
last bit of an abort sequence. A hardware interrupt is generated only if the corresponding
interrupt-enable bit (FDL_PR2 bit 4) is set. This status bit is cleared to 0 by a read of this
register. This interrupt is not generated in the transparent mode.
FDL Receiver Overrun.
This bit is set to 1 when the receive FIFO has overrun its
capacity. A hardware interrupt is generated only if the corresponding interrupt-enable bit
(FDL_PR2 bit 5) is set. This status bit is cleared to 0 by a read of this register*.
FDL Receiver Idle.
This bit is set to 1 when the FDL receiver is idle (i.e., 15 or more
consecutive ones have been received). A hardware interrupt is generated only if the cor-
responding interrupt-enable bit (FDL_PR2 bit 6) is set. This status bit is cleared to 0 by a
read of this register. This interrupt is not generated in the transparent mode.
FDL Receive ANSIBit Codes.
This bit is set to 1 when the FDL receiver recognizes a
valid T1.403 ESF FDL bit code. The receive ANSIbit code is stored in register
FDL_SR3. An interrupt is generated only if the corresponding interrupt enable of register
FDL_PR6 bit 7 = 1. This status bit is cleared to 0 by a read this register.
1
FTEM
2
FTUNDABT
3
FRF
4
FREOF
5
FROVERUN
6
FRIDL
7
FRANSI
相關PDF資料 |
PDF描述 |
|---|---|
| T7630 | Dual T1/E1 5.0 V Short-Haul Terminator (Terminator-II)(雙 T1/E1 5.0V短距離通信終端器) |
| T8100A | H.100/H.110 Interface and Time-Slot Interchangers |
| T8102A | H.100/H.110 Interface and Time-Slot Interchangers |
| T8105A | H.100/H.110 Interface and Time-Slot Interchangers |
| T8100 | H.100/H.110 Interface and Time-Slot Interchanger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T7630426 | 制造商:COOPER INDUSTRIES 功能描述:CC ACCESYS / #2450 3/8 Spring Snap Link Stainless Steel UPC Tagged |
| T-7630-TL2-DB | 制造商:Legerity 功能描述:5V DUAL T1/E1 SHORT-HAUL TERMINATOR |
| T7633 | 制造商:AGERE 制造商全稱:AGERE 功能描述:Dual T1/E1 3.3 V Short-Haul Terminator |
| T7645036 | 功能描述:手工工具 Campbell Snap Link #2450, 7/16", Steel RoHS:否 制造商:Molex 產品:Extraction Tools 類型: 描述/功能:Extraction tool |
| T7645106 | 制造商:COOPER INDUSTRIES 功能描述:CC ACCESYS / #7350 1/8 Quick Link Steel Zinc Plated UPC Tagged |
發布緊急采購，3分鐘左右您將得到回復。