- 您現在的位置：買賣IC網 > PDF目錄371179 > T7630 T7630 Dual T1/E1 5.0 V Short-Haul Terminator (Terminator-II) PDF資料下載
參數資料
| 型號： | T7630 |
| 英文描述： | T7630 Dual T1/E1 5.0 V Short-Haul Terminator (Terminator-II) |
| 中文描述： | T7630雙T1/E1的5.0V的短途終結者（終結者-Ⅱ） |
| 文件頁數： | 195/210頁 |
| 文件大?。?/td> | 3075K |
| 代理商： | T7630 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁當前第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁
Lucent Technologies Inc.
Lucent Technologies Inc.
195
Preliminary Data Sheet
October 2000
T7630 Dual T1/E1 5.0 V Short-Haul Terminator (Terminator-II)
FDL Parameter/Control Registers (800—80E; E00—E0E)
(continued)
Table 192. FDL Transparent Control Register (FDL_PR9) (809; E09)
* The octet boundary is relative the first receive clock edge after the receiver has been enabled (ENR, FDL_PR1 bit 2 = 1).
Table 193. FDL Transmit ANSIESF Bit Codes (FDL_PR10) (80A; E0A)
Bit
0—2
Symbol
FOCTOF0—
FOCTOF2
Description
FDL Octet Offset (Read Only).
These bits record the offset relative to the octet bound-
ary when the receive character was matched. The FOCTOF bits are valid when register
FDL_PR9 bit 3 (FMSTAT) is set to 1. A value of 111 (binary) indicates byte alignment.
Match Status (Read Only).
When this bit is set to 1 by the receive FDL unit, the receiver
match character has been recognized. The octet offset status bits (FDL_PR9 bit[2:0])
indicates the offset relative to the octet boundary* at which the receive character was
matched. If no match is being performed (register FDL_PR9 bit 5 = 0), the FMSTAT bit is
set to 1 automatically when the first byte is received, and the octet offset status bits (reg-
ister FDL_PR9 bit 0—bit 2) are set to 111 (binary).
Frame-Sync Align.
When this bit is set to 1, the receive FDL unit searches for the
receive match character (FDL-PR8) only on an octet boundary. When this bit is 0, the
receive FDL unit searches for the receive match character in a sliding window fashion.
Pattern Match.
FMATCH affects both the transmitter and receiver. When this bit is set to
1, the FDL does not load data into the receive FIFO until the receive match character
programmed in register FDL_PR8 has been detected. The search for the receive match
character is in a sliding window fashion if register FDL_PR9 bit 4 is 0, or only on octet
boundaries if register FDL_PR9 bit 4 is set to 1. When this bit is 0, the receive FDL unit
loads the matched byte and all subsequent data directly into the receive FIFO. On the
transmit side, when this bit is set to 1 the transmitter sends the transmit idle character
programmed into register FDL_PR5 when the transmit FIFO has no user data. The
default idle is to transmit the HDLC ones idle character (FF hexadecimal); however, any
value can be used by programming the transmit idle character register FDL_PR5. If this
bit is 0, the transmitter sends ones idle characters when the transmit FIFO is empty.
FDL Transparent Mode.
When this bit is set to 1, the FDL unit performs no HDLC pro-
cessing on incoming or outgoing data.
Reserved.
Write to 0.
3
FMSTAT
4
FALOCT
5
FMATCH
6
FTM
7
—
Bit
0—5
Symbol
FTANSI0—
FTANSI5
—
FTANSI
Description
FDL ESF Bit-Oriented Message Data.
The transmit ESF FDL bit messages are in the
form 111111110X
0
X
1
X
2
X
3
X
4
X
5
0, where the order of transmission is from left to right.
Reserved.
Write to 0.
Transmit ANSIBit Codes.
When this bit is set to 1, the FDL unit will continuously trans-
mit the ANSIcode defined using register FDL_PR10 bit 0—bit 5 as the ESF bit code
messages. This bit must stay high long enough to ensure the ANSIcode is sent at least
10 times.
6
7
相關PDF資料 |
PDF描述 |
|---|---|
| T7630 | Dual T1/E1 5.0 V Short-Haul Terminator (Terminator-II)(雙 T1/E1 5.0V短距離通信終端器) |
| T8100A | H.100/H.110 Interface and Time-Slot Interchangers |
| T8102A | H.100/H.110 Interface and Time-Slot Interchangers |
| T8105A | H.100/H.110 Interface and Time-Slot Interchangers |
| T8100 | H.100/H.110 Interface and Time-Slot Interchanger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T7630426 | 制造商:COOPER INDUSTRIES 功能描述:CC ACCESYS / #2450 3/8 Spring Snap Link Stainless Steel UPC Tagged |
| T-7630-TL2-DB | 制造商:Legerity 功能描述:5V DUAL T1/E1 SHORT-HAUL TERMINATOR |
| T7633 | 制造商:AGERE 制造商全稱:AGERE 功能描述:Dual T1/E1 3.3 V Short-Haul Terminator |
| T7645036 | 功能描述:手工工具 Campbell Snap Link #2450, 7/16", Steel RoHS:否 制造商:Molex 產品:Extraction Tools 類型: 描述/功能:Extraction tool |
| T7645106 | 制造商:COOPER INDUSTRIES 功能描述:CC ACCESYS / #7350 1/8 Quick Link Steel Zinc Plated UPC Tagged |
發布緊急采購，3分鐘左右您將得到回復。